Electronics International MVP-50P, Installation Instructions Manual

Page: 7 / 105

3.0 Install the EDC Wire Harnesses and Route Wires ---------------------------------------------- 33
3.1 Attach the three EDC 37-pin wire harnesses to the EDC: ---------------------------- 35
3.2 Connect the EDC Harness to the Temperature Probes: -------------------------------- 35
3.3 Connect the EDC Harness to the Pressure Transdcueres: ----------------------------- 35
3.4 Connect the EDC Harness to the Shunt: -------------------------------------------------- 36
3.5 Connect the EDC Harness to the Fuel Flow Transducer: ----------------------------- 36
3.6 Connect the EDC Harness to the Existing Capacitive Fuel Level System: ---------- 36
3.7 Connect the RFLM-4-x Harness to the EDC Connector and to the Resistive
Fuel Level Sensor: ----------------------------------------------------------------------------- 37
3.8 Connect the EDC Harness to the Capacitive Fuel Level Probe: --------------------- 37
3.9 Connect the EDC Harness to the P-300M Fuel Level Senders: ---------------------- 38
3.10 Connect the EDC Harness (Volts Meassurement Pin) to the Bus: ----------------- 38
3.11 Connect the EDC Harness to the RPM Signals: ---------------------------------------- 38
3.12 Setup the EDC for a 4 or 6-Cylinder Engine: ------------------------------------------- 38
3.13 Connect the EDC Harness to the VI-221's (Voltage Interface Units): ------------- 38
3.14 Connect the EDC Harness to Power and Ground: ------------------------------------ 39
3.15 Route the EDC RS422 Wires to the MVP Connector: -------------------------------- 39
4.0 Install the MVP Wire Harness and Route the Wires ------------------------------------------- 40
4.1 Attacht the MVP 25-pin D-sub Connector to the MVP: ------------------------------- 42
4.2 Connect the EDC RS422 Wires to the MVP RS422 Wires: --------------------------- 42
4.3 Connec the MVP Harness to the Master Warning and Caution Lights: ------------- 42
4.4 Connec the MVP Harness to the Voice Alarm Control Panel (AV-17CP): --------- 42
4.5 Connec the MVP Harness to the Audio Panel: ------------------------------------------- 43
4.6 Connec the MVP Harness to the External Intensity Control Pot (CP-1): ----------- 43
4.7 Connec the MVP Harness to the Moving Map Data Out from the GPS: ----------- 43
4.8 Connec the MVP Harness to the Fuel Data Input on the GPS: ----------------------- 44
4.9 Connec the MVP "Transmit Lockout Input" pin to the Transmit Key: ------------- 44
4.10 Connec the MVP Harness to Power and Ground: ------------------------------------- 44
4.11 Connec the MVP Harness to the CO-Guardian CO Detector: ---------------------- 44
5.0 Mandatory System Setup and Checkout --------------------------------------------------------- 45
5.1 Power-On Checkout -------------------------------------------------------------------------- 47
5.2 Perform all Steps Listed in the "MVP-50P Setup Checklist" ------------------------ 47
5.3 Ground Run Checkout ------------------------------------------------------------------------ 47
5.4 First Flight Checkout -------------------------------------------------------------------------- 48
5.5 Read the "Warranty/Agreement" and the "Important Notice" ----------------------- 48
6.0 Installation Data -------------------------------------------------------------------------------------- 50
6.1 Instructions for Continued Airworthiness (ICA): ----------------------------------------- 52
6.2 Airworthiness Limitations: -------------------------------------------------------------------- 52
6.3 Working With Connectors: -------------------------------------------------------------------- 52
6.3.1 Installing a Red Slip-on Connector onto a TC or Tin Copper Wire: ---------- 52
6.3.2 Installing a Yellow Precision TC Connector onto a TC Wire: ----------------- 53
6.3.3 Installing a D-sub Pin onto a TC or Tin Copper Wire: -------------------------- 53
Contents
(Page 2 of 3)