Electronics International M-1 Operating And Installation Instructions Download Page 5

Page: 5 / 14

Contents

Warranty.............................................................................

22222

Operation Instructions ........................................................

33333

Instrument: ...............................................................................

Analog Display: .........................................................................

Digital Display: ..........................................................................

Installation Instructions .......................................................

44444

Important Information and Initial Check Out: .............................

Route The Circular Connector: ..................................................

Route the Power and Ground Wires: ..........................................

Route the Backlight Wires: ........................................................

Route the (Optional) External Warning Control Line: ..................

Install the Instrument in the Panel: ............................................

Connect the Circular Connector to the Instrument: ....................

Connect the Manifold Pressure Line: .........................................

Check Instrument Operation: ....................................................

Wiring Diagram .................................................................

88888

M-1 Circular Connector ......................................................

99999

Specifications and Operating Features ..................................

1 0

STC Information ................................................................

1 1

Summary of Contents for M-1















Search results

Summary of Contents for M-1

Reviews:

Related manuals for M-1

Brands by name

Popular brands

Electronics International M-1, Operating And Installation Instructions

Search results

Summary of Contents for M-1

Reviews:

Related manuals for M-1

Brands by name

Popular brands