manualshive.com logo in svg

Electrolux Z4640 SERIES, Owner'S Manual

Share
Download
Electrolux Z4640 SERIES Owner'S Manual Download Page 15

15

Pre-Motor Filter

Check  the  pre-motor  filter  each  time  the  cyclonic  dust  cup  is 

emptied. Clean or replace as needed.

To Clean Pre-Motor Filter

1.  Remove  filter  centered  in  the  bottom  of  the  dust  cup 

compartment.

2.  Shake filter to remove excess dust. If necessary, the filter can 

be cleaned by vacuuming with another cleaner or washing with 

mild detergent.

3.  Reinstall filter after completely dry.

NOTE:  If  rubber  gasket  separates  from  motor  adapter,    

reposition  securely  on  top  edge  before  using 

cleaner.

Use GENUINE ELECTROLUX replacement pre-motor filters.

1

3

Motor 

Adapter

Pre-Motor Filter

Motor 

Adapter 

Gasket

To  remove  HEPA 

cartridge

  filters  and 

Washable HEPA filters

1.  Push down latch and pull filter cassette back.
2.   Then lift filter up and remove.

To  replace  HEPA 

cartridge

  filters  and 

Washable HEPA filters

1.   Place bottom tabs of filter cassette into slots.
2.   Rotate filter toward cleaner.
3.  Push upward on the latch to secure into place.

NOTE:  To have the benefit of a sealed HEPA system, 

you must use one of the HEPA 

cartridge

 filter 

systems.

NOTE:  For rinsing instructions of the Washable HEPA 

filter  see  the “Rinsing  Directions  for  Rinsable 
Filters on the previous page.

CAUTION:  If your cartridge does not say Washable HEPA 

Filter” it is not reusable - do not wash.

 

HEPA Cartridge Filters and Washable Hepa Filters. 

(Only for models with HEPA cartridge.)

Check  the  HEPA  filters  each  time  the  dust  cup  is  emptied.  Replace  twice  a  year  or  after  every  six  times  the  dust  cup  is 
emptied.

Latch

Filter Cartridge (One 

complete unit)

Tabs

Summary of Contents for Z4640 SERIES





















Reviews:

No comments

Brands by name

Popular brands

Load more brands