manualshive.com logo in svg

Electrolux Z4640 SERIES, Owner'S Manual

Share
Download
Electrolux Z4640 SERIES Owner'S Manual Download Page 10

10

HOW TO MAINTAIN

The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the cyclonic 
dust cup, belt, and brush roll often.

To Change Dust Cup Pleated Filter:

NOTE:  Turn off the switch and unplug the electrical cord before changing the pleated filter. Never operate the vacuum 

cleaner without the dust cup or the pleated filter assembly.

Check and clean the pleated filter once a month to maintain good performance. The filter can be cleaned by washing 
with mild detergent and warm water. Be sure pleated filter is completely dry before reinstalling.

To clean the Pleated Filter:

1.  Grasp yellow filter frame and twist counter clockwise to remove.

2.  Shake vigorously and brush off dust and lint.

3.  If filter needs further cleaning, wash in warm water using a mild detergent.

4. 

Do not submerge gray dust cup lid, wipe only with a damp cloth.

5.  When all parts are completely dry, replace filter on gray dust lid by twisting clockwise to snap and lock in place.

Use a Genuine Electrolux replacement pleated 

filter. Call Electrolux on 08706 055055 for 

assistance.

1

3

Gray Filter 

Assembly

Pleated 

Filter

1

Slots

Tabs

Remove dust cup by pulling latch (1) forward, pivoting dust cup 

out and lifting up. To replace dust cup, put bottom of dust cup in 

place by aligning 

tabs

 in 

slots

 and pivot top assembly  back into 

place. Push down on latch (1), making certain that latch securely 

snaps and overlaps tabs at top of dust cup.

Summary of Contents for Z4640 SERIES





















Reviews:

No comments

Brands by name

Popular brands

Load more brands