Electrolux N7E, Installation And Operating Manual

Page: 20 / 32

20
• Turn one of the two plates inside the appliances 180℃
(Fig.1C)
• From inside the control panel of the same appliance, join
them at the front side, screwing one M5x40 Hex Head
screw (supplied) on the opposite insert (Fig.1E).
• From the rear of the appliances, insert the coupling plate
(provided) in the side slots on the back panels. Secure the
plate with two flat head M5 screws provided (Fig.1F).
E E..4 4..1 1 F Fllo oo orr F Fiixxiin ng g
To avoid accidental tipping of built-in half-module appliances
installed separately, fix them to the floor carefully following the
instructions enclosed with the corresponding accessory
(F206136).
E E..4 4..2 2 IIn nsstta alllla attiio on n O On n B Brriid dg ge e,, C Ca an nttiille evve err F Frra am me e O Orr
C Ce em me en ntt P Plliin ntth h
Carefully follow the instructions enclosed with the correspond-
ing accessory. Follow the instructions supplied with the
optional product chosen.
E E..4 4..3 3 S Se ea alliin ng g G Ga ap pss B Be ettw we ee en n A Ap pp plliia an ncce ess
Follow the instructions supplied with the optional sealing paste
pack.
E E..5 5 G Ga ass,, e elle eccttrriicciittyy a an nd d w wa atte err cco on nn ne eccttiio on nss
• Any installation work or maintenance to the supply system
(gas, electricity, water) must only be carried out by the utility
company or an authorised installation technician.
• Refer to the appliance dataplate for the product code.
• See the installation diagram for the type and position of
appliance connections.
E E..6 6 G Ga ass cco on nn ne eccttiio on n
E E..6 6..1 1 G Ga ass C Co on nn ne eccttiio on nss
E.6.1.1Introduction
C CA AU UT TIIO ON N
This appliance is arranged and tested to
operate with G20 gas 20 mbar; to convert
it to another type of gas, follow the
instructions in E.6.1.6
Conversion to
another type of gas paragraph of this
section.
E.6.1.2Fume exhaust
For A AU US ST TR RA AL LIIA A ventilation must be in accordance with
Australian building codes and kitchen exhaust hoods must
comply with AS/NZS1668.1 and AS 1668.2
Position type “A1“ appliances under an extraction hood to
ensure removal of fumes and steam produced by cooking.
Type “A1“ appliances
• S SU UB B C CL LA AU US SE E 6 6..2 2..1 1 iiss n no ott rre elle evva an ntt ffo orr A Au ussttrra alliia an n
sstta an nd da arrd d..
E.6.1.3Before connecting
• Make sure the appliance is arranged for the type of gas to
be used. Otherwise, carefully follow the instructions given in
E.6.1.6
Conversion to another type of gas paragraph of this
section.
• Fit a rapid gas shutoff tap/valve ahead of each appliance.
Install the tap/valve in an easily accessed place.
• Clean the pipes to remove any dust, dirt or foreign matter
which could block the supply.
• The gas supply line must ensure the gas flow necessary for
full operation of all the appliances connected to the system.
A supply line with insufficient flow will affect correct
operation of the appliances connected to it.
IIM MP PO OR RT TA AN NT T
Incorrect levelling of the appliance can
affect
combustion and cause
malfunctioning.
E.6.1.4Connection
• See the installation diagram for the position of the gas
connection on the bottom of the appliance.
• Remove the plastic protection (if present) from the gas
union before connecting.
• After installation, use soapy water to check connections for
leaks.
• The gas connection is male 1/2” BSP ((O ON NL LY Y F FO OR R
A AU US ST TR RA AL LIIA A)).
1A
180
1B
1C
N7E
N9E
1E
1F
1D
N7E N9E