Electrolux LAVALOGIC EWM 3000 Service Manual Download Page 57

Page: 57 / 59

- 57 -

599 51 13-50 EN

DGS-TDS-N 11.2004 C.D.

10.3 Access from the top side of the appliance

10.3.1 Pressure switches

Abb.: 21

NTC Sensor

10.2.5 NTC sensor

Abb.: 22

Cross bar

Pressure switch

The pressure switches are clipped in the right upper area of the cross bar.

Remove the worktop; instructions 10.1.1

Pull off the pressure switch hose.

Mark the plugs and then pull them off.

Now snap out the pressure switch from the support (cross bar).

The NTC sensor (temperature sensor) is inserted in the rear side of the tub at the side next to the heating

element.

Carry out an emergency drain of the appliance

Take off the rear plate; instructions 10.2.1

Disconnect the electrical connections

Pull the NTC sensor out of the sealing

Pressure sensor

Summary of Contents for LAVALOGIC EWM 3000




























































Search results

Summary of Contents for LAVALOGIC EWM 3000

Reviews:

Related manuals for LAVALOGIC EWM 3000

Brands by name

Popular brands

Electrolux LAVALOGIC EWM 3000, Service Manual

Search results

Summary of Contents for LAVALOGIC EWM 3000

Reviews:

Related manuals for LAVALOGIC EWM 3000

Brands by name

Popular brands