Electrolux LAVALOGIC EWM 3000 Service Manual Download Page 18 | Manualshive

Page: 18 / 59

background image

- 18 -

599 51 13-50 EN

DGS-TDS-N 11.2004 C.D.

© Electrolux

4.4

Variomatic loosening-up spin

4.4.1

Activate variomatic loosening-up spin

Programming before program start:

-

Set selection switch to position short spin.

-

Keep stain button pressed at least 5 sec.

-

To confirm the end LED is flashing for 5 sec.

-

While the end LED is flashing, release the stain button.

-

When the flashing has stopped, the variomatic loosening-up spin is active.

4.4.2

Deactivate variomatic loosening-up spin

Programming before program start:

-

Set selection switch to position short spin.

-

Keep stain button pressed at least 5 sec.

-

Immediately when pressing the button, the end LED is flashing.

-

After 5 sec the flashing stopps and the LED is lit continuously for 5 sec.

-

While the end LED is lit continuously, release the stain button.

-

After the end LED has stopped lighting, the variomatic loosening-up spin is cancelled.

In order to check whether the loosening-up spin is activated, set the program selection switch

to short spin and press the stain button shortly. When the end LED is flashing,

the loosening-up spin is activated.

«
...
16
17
18
19
20
...
»

Summary of Contents for LAVALOGIC EWM 3000




























































Reviews:

No comments

Related manuals for LAVALOGIC EWM 3000

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: Campomatic Pages: 16

Executive Elite

Brand: IFB Pages: 31

Brand: Wassermann Pages: 28

Brand: Hanseatic Pages: 78

Brand: Easy-Kleen Pages: 28

Brand: Silverline Pages: 76

Brand: LVO Manufacturing Pages: 34

Aquarius WDD 756

Brand: Hotpoint Pages: 16

Brand: Zanussi Pages: 36

Brand: Zanussi Pages: 32

WF8804FS(A/F/G/H/S/V/W/Z)

Brand: Samsung Pages: 72

Brand: Samsung Pages: 40

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 24

Brand: Lamona Pages: 12

Brand: BorMann Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands