Electrolux LAVALOGIC EWM 3000 Service Manual Download Page 56

Page: 56 / 59

- 56 -

599 51 13-50 EN

DGS-TDS-N 11.2004 C.D.

10.2.3Motor

The drive motor is fastened to the tub with 4 screws.

Take off the rear plate; instructions 10.2.1

Draw off the motor plug.

Remove the drive belt.

Now unscrew the motor

Belt

Motor

Motor plug

Motor screws

10.2.4 The heating element

The heating element is inserted in the rear side of the tub and the contacts are protected by tahe clipped

cover. Tightening the pressure plate to the heating flange expands the sealing and thus fastens the

heating element.

Carry out an emergency drain of the appliance.

Take off the rear plate; instructions 10.2.1

Remove the cover

Disconnect the electrical connections

Untighten the flange nut to the end of the thread and press in the stud bolt with the nut

as far as to the pressure plate (sealing gets released).

Loosen the heating element by moving it laterally and pull it out of the tub.

Abb.: 19

Abb.: 20

cover of

heating

element

electrical

connections

Summary of Contents for LAVALOGIC EWM 3000




























































Search results

Summary of Contents for LAVALOGIC EWM 3000

Reviews:

Related manuals for LAVALOGIC EWM 3000

Brands by name

Popular brands

Electrolux LAVALOGIC EWM 3000, Service Manual

Search results

Summary of Contents for LAVALOGIC EWM 3000

Reviews:

Related manuals for LAVALOGIC EWM 3000

Brands by name

Popular brands