Page 30
Induction Cooktop Error Codes continued on next page
NOTE: If multiple changing error codes are displayed check for disconnected wires or cables.
Error Possible Cause or Condition
Suggested Corrective Action
32
or
72
Low voltage output from 12V supply on
fi
lter board in the 3 cook zone induction
module.
-Test all cables & connections on
fi
lter circuit board in
the 3 zones induction module.
-Replace the
fi
lter circuit board in the 3 zones induction
module .
-Replace generator circuit boards in the 3 zones induction
module
33
or
73
Improper voltage output from
fi
lter board in
the 3 cook zone induction module.
34
Communication failure between
fi
lter board
and power boards in the 3 cook zones
induction module / left side cooking zones.
- Check cable between
fi
lter board X12 and
generator board X10
- Replace the
fi
lter circuit board in the 3 zones induction
module .
- Replace generator circuit board in the 3 zones
induction module.
35
or
75
AC input voltage too low in the 3 cook
zones
induction module.
- Verify AC input voltage at the cooktop input.
- Verify AC main input cables, screws and jumpers.
- Replace the
fi
lter board in the 3 zones induction
module
36
Communication error between main touch
control and
fi
lter board.
(3 cook zones induction module / left side
cooking zones)
- Verify all communication cables between user interface and both
induction generator modules.
- Replace the
fi
lter circuit board in the 3 zones induction module .
- Replace generator circuit board (dual) in the 3 zones induction
module .
37
Heat sink temperature sensor break
(3 zones induction module / left side cook-
ing zones)
-Replace the generator circuit board (LF/LRl) in the 3 zones
induction module
39
Con
fi
guration mismatch between the User
Interface and the induction module (occurs
when one of the 2 zone induction modules
is replaced)
- To resolve this error, Press and hold WARM key, then press
Right Front zone ON key until beep (keep holding WARM)
release Right Front zone ON key and press Left Front zone ON
key until beep & con
fi
g starts.
- Replace the
fi
lter circuit board in the 3 zones induction module .
40
Communication failure between main touch
control and
fi
lter board.
- Verify AC input at the (2 zones induction housing) (X50 / X52).
- Verify Lin Bus harness cable from X68/X67 on right side
fi
lter
board (2 zones induction module) to X20 on the left side
fi
lter
board (3 zones induction module).
- Verify the lin communication wire at the timer input at
X4/X5 pin 2.
45
Incoming power supply low voltage
- Verify incoming power supply to cooktop
51
LF Element temperature sensor break
- Verify Element temperature sensor is correctly connected to the
generator circuit board.
- Replace element if temperature sensor resistor value is not
approximatively 1000 ohms (blue wires) at room temperature.
- Replace associated generator circuit board.
52
LR Element temperature sensor break
53
Center Element temperature sensor break
54
RR Element temperature sensor break
55
RF Element temperature sensor break
60
Touch: general hardware error, keys
- Replace main power touch control.
- Replace cook zones touch controls
61
LF Element temperature sensor too hot
- Verify cooktop ventilation is correct (airway and fan).
- Verify Element temperature sensor is correctly connect to the
generator circuit board.
- Replace element if temperature sensor resistor value is not
approximatively 1000 ohms (blue wires) at room temperature.
- Replace associated generator circuit board.
62
LR Element temperature sensor too hot
63
Center Element temperature sensor too hot
64
RR Element temperature sensor too hot
65
RF Element temperature sensor too hot
ELECTROLUX ICON 36” Induction Cooktop Error Codes
