Electrolux ICON E23BC69SPS3 Use And Care Manual Download Page 24

Page: 24 / 43

24 Automatic Ice Maker & Water Dispenser

Ice maker/dispenser tips

• If your refrigerator is not connected to

a water supply or the water supply is

turned off, turn off the ice maker by

holding the On/Off soft-touch icon for

three seconds.

• The following sounds are normal when

the ice maker is operating:

- Motor running

- Ice dropping into ice bin

- Water valve opening or closing

- Running water

• If you need a large quantity of ice

at one time, it is best to get cubes

directly from the ice bin.

• Ice cubes stored too long may

develop an odd flavor. Empty the ice

bin as explained below.

• When dispensing cubed ice, it is

normal to have a small quantity of little

pieces along with the whole cubes.

Removing Ice Bin

Cleaning the ice maker

Clean the ice maker and ice bin at regular

intervals, especially prior to vacation or

moving.
1 Turn off

the ice

maker.

2 Remove

the ice

bin by

pulling

straight

out.

3 Empty

and

carefully

clean the ice bin with mild detergent.

Do not use harsh or abrasive

cleaners. Rinse with clear water.

4 Allow the ice bin to dry completely

before replacing.

5 Replace the ice bin. Turn the ice

maker on.

Adjusting Ice Bin Auger

Auger

Remove and empty the ice bin if:

• An extended power failure (one hour

or longer) causes ice cubes in the

ice bin to melt and freeze together,

jamming the dispenser mechanism.

• You do not use the ice dispenser

frequently. Ice cubes will freeze

together in the bin, jamming the

dispenser mechanism.

Remove the ice bin and shake to loosen

the cubes or clean as explained above.

IMPORTANT

When removing or replacing the ice bin,

DO NOT rotate the auger in the ice bin.

If the auger is accidentally rotated, you

must realign the auger by turning it in 45

degree turns (see below) until the ice bin

fits into place with the drive mechanism.

If the auger is not properly aligned when

replacing the ice bin, the refrigerator will

not dispense ice. The fresh food door

also may not close properly causing

warm air to leak into the fresh food

compartment.

CAUTION

If the water supply to your refrigerator

is softened, be sure the softener is

properly maintained. Chemicals from

a water softener can damage the ice

maker.

NOTE

Dispenser models allow for an additional

freezer ice maker to be installed. Call

1-877-435-3287 for more information.

CAUTION

NEVER use an ice pick or similar sharp

instrument to break up the ice. This

could damage the ice bin.
To loosen stuck ice, use warm water.

Before replacing the ice bin, make sure

it is completely dry.

Summary of Contents for ICON E23BC69SPS3












































Search results

Summary of Contents for ICON E23BC69SPS3

Reviews:

Related manuals for ICON E23BC69SPS3

Brands by name

Popular brands

Electrolux ICON E23BC69SPS3, Use And Care Manual

Search results

Summary of Contents for ICON E23BC69SPS3

Reviews:

Related manuals for ICON E23BC69SPS3

Brands by name

Popular brands