manualshive.com logo in svg

Electrolux GA55GL201, User Manual

Share
Download
Electrolux GA55GL201 User Manual Download Page 32

32 electrolux care and cleaning

Cleaning the spray arms
Regularly check the nozzles in the 3
spray arms for blockages. If
necessary clean the nozzles with a
piece of fine wire or a fine needle and
a strong water jet. 

Do not damage the nozzle openings.

3. Clean the spray arm and the fixing

screw.

4. Fasten the spray arm with the

fixing screw (A) by turning it
clockwise.

Ceiling spray arm
1. Undo the fixing screw (A) by

turning it anti-clockwise.

2. Pull the spray arm off the shaft.

A

Upper basket spray arm
1. Remove the upper basket spray

arm by turning it laterally.

2. Clean spray arm nozzles.
3. To replace the spray arm, press

upwards until you feel it snap into
place.

3. Clean the spray arm and the fixing

screw.

4. Fasten the spray arm with the

fixing screw (B) by turning it
clockwise.

Lower spray arm
1. Undo the fixing screw (B) by

turning it anti-clockwise.

2. Pull the spray arm off the shaft.

B

117986 11/1en  16-06-2007  9:30  Pagina 32

Summary of Contents for GA55GL201





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands