Electrolux EWW1142ADSA, User Manual, Page: 23 / 92

Alternatively , before pressing the
“Start/Pause” touchpad, you can press
the “Spin ” touchpad to change the
spin speed. You can select “No Spin
( )”, if you want the machine to
only drain the water.
22 www.electrolux.com.cn
When the program is completed and
the door lock indicator “ ” goes off,
you can open the door.
5.10 When The Washing
Program Is Completed, But
There Is Water In The Drum
The drum turns regularly to prevent
the creases in the laundry.
(Option “Rinse Hold ” is used)
You must drain the water to
open the door.
The indicator “Start/Pause” flashes to
remind you to drain the water.
−
−
−
The appliance stops automatically.
The acoustic signal will operate.
The display will show “ ”.
The indicator of the touchpad
Start/Pause goes off.
−
−
−
−
−
−
−
−
The door lock indicator “ ” goes off.
Remove the laundry from the
appliance. Make sure that the drum is
empty.
Keep the door partly open, to prevent
the mildew and odours.
Turn off the water tap.
5.9 At The End Of The Program
At the end of the program, the time
remaining can suddenly decrease from
7 minutes or less to 0 due to the
overestimated total program time during
the load sensing phase. In some cases
(with perfectly balanced load) the
program time can be shorter than the
time estimated after the load sensing
phase is completed. This is a normal
behavior of the machine and not a cause
for concern as it does not compromise its
performance.
5.11 AUTO Off Mode
The AUTO Off mode automatically
deactivates the appliance to decrease
the energy consumption when:
You do not press any buttons for 5
minutes before you press “Start/Pause”.
Press the “On/Off” button to activate
the appliance again.
After 5 minutes from the end of the
washing program.
Press the “On/Off” button to
reactivate the appliance. Display will
show the end of the last wash.
−
−
Press any touchpad again to show
the last wash program.
−
NOTE
The door lock indicator “ ” is on.
The door stays locked.
1.
To drain the water:
Press the “Start/Pause ” touchpad.
The appliance drains the water and
spins with the maximum spin speed
for selected program.
2.
Press the “On/Off” button to deactivate
the appliance.
3.
After approximately 18 hours, if you do
not press Start/Pause touchpad, the
appliance will drain and spin automatically
(except for “Wool” program) .
NOTE
If a program is not compatible
with the drying option selected,
the symbol “ ” will flash on
display.
After anti-crease phase finish, the
door lock indicator “ ” goes off.
The display will show “ ”.
The display will show “ ” and
“Anti Crease ( )” icon is lit.
The door lock indicator “ ” is still
on.
The appliance will perform the anti-
crease phase for approximately 10
minutes.
23
If you wish to open the door
during the anti-crease phase
or interrupt it, press
Start/Pause touchpad.
The acoustic signal will operate.
-
-
-
-
DAILY USE - DRYING (Only) 6.
The water tap must be open
and the drain hose must be
positioned in the sink or
connected to the drain pipe.
Load the laundry. Make sure the load
size does not exceed the maximum
drying capacity of the machine.
2.
Press the On/Off button to turn on the
machine.
1.
Turn the knob to set a wash program
which can select drying option (refer to
Program Chart on page 11), according
to your clothes then press Wash/Dry
Mode touchpad to switch your
machine to
Dry Only ( ) mode
.
3.
If you wish to select an automatic
drying, press the “Dryness Level”
option until the icon corresponding to
the required dryness level appears on
the display. (see page 15)
4.
5.
Press “Start/Pause ” touchpad to
start the program. The time remaining
is updated every minute.
6.
At the end of the program :
7.
Press “On/Off” button to switch the
machine off.
8.
9.
If you wish to select a timed drying,
press the “Time Dry ” option
repeatedly until desired drying time
reached. (see page 16)
At the end of each drying cycle,
the temperature of your clothing
will be high. For your safety,
please leave the door open to
let your clothes cool before
removing your laundry.
DAILY USE - WASHING & DRYING (Non-Stop Program) 7.
Load the laundry and add detergent
and fabric softener. Make sure the load
size does not exceed the maximum
drying capacity of the machine.
1.
Turn the knob to set a wash program
which can select drying option (refer to
Program Chart on page 11), according
to your clothes then press Wash/Dry
Mode touchpad to switch your machine
to Wash and Dry ( ) mode .
2.
Select the required options by
pressing the relevant touchpads. If
possible, do not select a spin speed
lower than that proposed by the
machine to avoid unnecessary longer
drying time therefore saving energy.
3.
Set the dryness level by pressing
“ Dryness e el ” touchpad.
The display will then show the whole
duration of wash & dry cycle.
4.
Start the program by pressing
Start/Pause touchpad. The time
remaining is updated every minute on
the display.
5.
7.1 Wash n ro ram Dryness e el O on
/