background image

8

 

www.electrolux.com

3. 

InstALLAtIon InstRUCtIons

3.1

 

Removing transit bolts

1.   Before operating the washer, remove the 

transit bolts (4eA) along with the rubber.

•  If the bolts are not removed, it may 

cause heavy vibration, noise and 

malfunction. (Fig.1)

3.2

 

Location of your washer

•   Check location where the washer will be 

installed. Make sure you have everything 

necessary for correct installation.

•   Do not place or store your washer below 

0°C (32°F) to avoid any damage from 

freezing.

•   Do not place or store laundry products 

on top of washer at any times.

•   Install the washer on the horizontal 

solid floor. If the washer is installed 

on an unsuitable floor, it could make 

considerable noise, vibrate severely 

and cause a malfunction. If the washer 

is not level, adjust leg up or down for 

horizontal installation.

•   Ventilation openings must not be 

obstructed by carpeting when the 

washer is installed on a carpeted floor.

•  Leave some space (right & left : 2.5cm, 

rear : 10 cm). (Fig.4)

2.   Unscrew the 4 bolts with the spanner 

supplied. Keep the 4 bolts and spanner 

for future use. (Fig.2)

•  Whenever the appliance is 

transported, the transit bolts must 

be refitted.

3.   Close holes with supplied cap holders. 

(Fig.3)

•   In case of built-in installation, the 

distance between top of the washer and 

bottom of upper plate should be at least 

3mm.

1

2

3

Approx.

2.5cm

Laundry

Tub

Washer

Drain Hose

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Summary of Contents for EWW1122DW













































Reviews: