background image

10

Water softener

To avoid scale deposits on the dishes and in the dish-
washer, the dishes must be washed with soft water,
i.e. water with a low lime content. The dishwasher
therefore has a built-in water softener, in which tap
water with a hardness of 4°d (German degree) and
harder is softened with the aid of special salt.

Your water supplier will be able to inform you
about the hardness and hardness range of
the water in your area.

The water softener can be set manually using the
water hardness switch; it can also be set electroni-
cally using the buttons on the control panel..

Setting the water softener

Adjusting the water softener to the setting given in the
table that corresponds to the hardness of the water in
your area:
The dishwasher must be switched off.

Setting manually:

1.

Open the dishwasher door.

2.

Remove the lower rack from the dishwasher.

3.

Turn the hardness range switch to 0 or 1 (see table).

4.

Replace the lower rack.

Setting electronically:

1.

Press the ON/OFF button.
The LED in the ON/OFF button will become illumi-
nated.

If other indicators are also illuminated, this
means that a dishwashing cycle has been
activated. The dishwashing cycle must be
deselected (RESET):
Press function buttons 

2

 and 

simultane-

ously for approx. 2 seconds. 
All other indicators will go out.

2.

Press the function buttons 

2

 and 

3

 simultaneously

and keep them pressed.
The LED indicators in function buttons 1 to 3 will
flash.

Water hardness

Adjusting the hardness setting

Number of flashes of the 

LED indicator for the end 

of the dishwashing cycle

in 

°d

1

 in 

mmol/l

2

 range

Manually

Electronically

51 - 70
43 - 50
37 - 42
29 - 36
23 - 28

9.0 - 12.5

7.6 - 8.9
6.5 - 7.5
5.1 - 6.4
4.0 - 5.0

IV

1

10 

3

9
8
7
6

10

9
8
7
6

0 *

19 - 22
15 - 18

3.3 - 3.9
2.6 - 3.2

III

5

4 *

5
4

11 - 14

1.9 - 2.5

II

3

3

4 - 10

0.7 - 1.8

I/II

2

2

under 4

under 0.7

I

1

no salt necessary

1

1)(°d) German degree, measure of the hardness of water
2)[mmol/l] millimol per litre, international unit for the hardness of water
3)On this setting the length of the dishwashing cycle may be slightly longer.

factory setting

Summary of Contents for ESF 6220









































Reviews: