30 electrolux.com.au
31
Activation and deactivation
Touch for 1 second to activate or deactivate the
appliance.
NOTE: When using cookware greater than 220mm the
manufacturer recommends that the centre zone be used.
Automatic switch off
THE APPLIANCE WILL AUTOMATICALLY
SWITCH OFF IF:
• All cooking zones are deactivated ( ).
• You do not set the heat setting after you activate
the appliance.
• You spill something or put something on the
control panel for more than 10 seconds (a pan,
a cloth, etc). An acoustic signal will sound and
the appliance will switch off. Remove the object
or clean the control panel.
• The appliance becomes too hot (e.g. when
a saucepan boils dry). Before you use the
appliance again, wait for the cooking zone to
cool down.
• You use incorrect cookware. The symbol will
come on and the cooking zone will deactivate
automatically after 2 minutes.
• A cooking zone is on for an extreme length of
time. The symbol will show and the appliance
will switch off. See below.
• The length of time that various settings can run
for before automatic switch off occurs are
shown below:
•
- 6 hours
•
- 5 hours
•
- 4 hours
•
- 1.5 hours
The heat setting
To adjust the heat setting, place your finger over the heat
bar graphic and slide across. The display will show the
adjusted heat setting.
NOTE: When you use cookware larger than 180mm the
manufacturer recommends that you put it on the rear
cooking zones.
Bridge function
The Bridge function connects two cooking zones together
and then operates them as one. You can use this function
for cookware larger than 260mm.
First set the heat setting for one of the cooking zones.
To activate the Bridge function touch . The indicator will
then come on. To set or change the heat setting, touch
either one of the control sensors.
To deactivate the Bridge function touch . The
indicator will go off. The cooking zones will then operate
independently.
Fast heat up function
You can get a required heat setting in a shorter time if
you activate the Fast Heat Up function. This will run the
cooking zone at maximum until the required heat setting
is reached.
To start the Fast Heat Up function for a cooking zone:
1.
Touch the power function sensor ( will come on).
2. Immediately touch your required heat setting. After 3
seconds comes on in the display.
3. The zone will heat at maximum until your required
heat setting is reached. The display will then change
from back to the required heat setting.
4. To stop the Fast Heat Up function change the
heat setting.
USING THE INDUCTION HOB
(CONTINUED)
Power management
Power management divides the power between the front
and rear zones for each of the 2 outer modules. See
illustration below:
This allows either the front or rear zone to draw power from
the other, if maximum power is required.
The timer
The count down timer
Use the count down timer to set how long you want a
cooking zone to operate.
IMPORTANT!
• To select the cooking zone: touch the sensor
again and again until the correct zone indicator
is displayed.
• Immediately, touch the sensor to set the time
(00 - 99 minutes). When the timer indicator of
the cooking zone starts to flash more slowly the
time will begin to count down.
• To see the remaining time select the cooking
zone with the sensor. The display will show
the remaining time.
• To change the count down timer: select the
cooking zone with the sensor and touch
or .
• To deactivate the count down timer select the
cooking zone with the sensor and touch
until the time counts down to 00. The timer
indicator will go out.
When the timer count down comes to an end, the cooking
zone will deactivate, the 00 will flash and a beep sound
will occur for 20 seconds.
The beep sound and flashing can be deactivated
immediately by touching the sensor.
USING THE INDUCTION HOB
(CONTINUED)
IMPORTANT!
When the two timer functions operate at the same time,
the display shows the count up timer first.
The Minute minder
You can use the timer as a minute minder when the
cooking zones are not in operation. Touch . Then
touch or of the timer to set the time. When the timer
countdown comes to an end, 00 will flash and a beep
sound will occur for 30 seconds. The beep sound and
flashing can be deactivated immediately by touching the
sensor.
The Stop+Go function
Use the function to close down all of your operating
cooking zones to the lowest heat setting with just one
touch.
• To activate this function touch . The indicator
will come on and the symbol will show on all
operating zones.
•
When
is activated, you cannot change the
heat setting.
• To deactivate this function touch again. The
heat setting that you set before comes back on.