background image

10

GB

MAINTENANCE

Grease filters

CLEANING METAL SELF- SUPPORTING GREASE FILTERS

Alarm signal reset

• Switch off the lights and extractor motor.
• Press button 

T3

 for at least 3 seconds, until the

leds start to flash.

Cleaning the filters

• The filters must be cleaned every 2 months of

operation, or more frequently for particularly
heavy usage, and can be washed in a dishwasher.

• Remove the filters one at a time by pushing them

towards the back of the group and pulling down
at the same time.

• Wash the filters, taking care not to bend them.

Allow them to dry before refitting.

• When refitting the filters, make sure that the

handle is visible on the outside.

Activated charcoal filter (Recirculation version)

REPLACING THE ACTIVATED CHARCOAL FILTER

Alarm signal activation

• In Recirculation version Hoods, the Filter saturation alarm can be enabled on installation or at a later

date. Turn the Lights and the suction Motor off.

• Disconnect the Hood using the Main switch or the double-pole switch on the mains power supply.
• Restore the connection by pressing and holding 

T1

.

• Release the button.  All five LEDs are turned on
• Within 3 seconds press 

T1

 until LEDs  T1 and T4 flash in confirmation:

LED flashes twice - Activated charcoal filter saturation alarm ENABLED
LED flashes once - Activated charcoal filter saturation alarm DISABLED

Summary of Contents for EFC 1540













Reviews: