Electrolux EBC54523AX, Instructions Manual

Page: 16 / 26

14 15
EN
• Remove the lid of the milk container.
• Fill the container with about 100 grams of milk for each
cappuccino to be prepared (fig. 23). Never exceed the MAX
level (corresponding to about 750 ml) marked on the con-
tainer. You should ideally use skimmed or semi-skimmed
milk at refrigerator temperature (about 5°C).
• Make sure the intake tube is correctly inserted in the rubber
washer (fig. 24) then replace the milk container lid.
• Position the frothed milk regulator (C1) between the words
CAPPUCCINO and CAFFELATTE printed on the milk container
lid.
The quantity of froth can be adjusted by moving the regu-
lator towards the word CAFFELATTE for a denser froth. Mo-
ving it towards the word CAPPUCCINO obtains a less dense
froth.
• Remove the hot water spout (fig 6) and attach the milk
container to the nozzle (fig. 25).
• Position the milk spout as shown in fig. 26 and then place a
sufficiently large cup under the coffee and milk spouts.
• Press the icon (fig. B12). “CAPPUCCINO...” is displayed
and after a few seconds, frothed milk flows out of the milk
spout into the cup below. (La fuoriuscita del latte si inter-
rompe automaticamente). (Delivery stops automatically).
• The appliance delivers coffee.
• The cappuccino is now ready. Sweeten to taste and, if desi-
red, sprinkle the froth with a little cocoa powder.
NOTE 1: While making cappuccino, the flow of frothed milk or
coffee can be interrupted by pressing the
icon (B12).
NOTE 2: If the milk in the container finishes while delivering fro-
thed milk, remove the container and add milk. Reattach and
press the
(B12) to request a cappuccino again.
NOTE 3: To ensure the complete cleanliness and hygiene of the
milk frother, always clean the circuits in the milk container lid
after making cappuccino.
“PRESS CLEAN!” flashes on the display.
• Place a recipient under the milk spout (fig. 26).
• Press the CLEAN button on the lid (C3) and hold down for at
least 5 seconds (fig. 26) to start the cleaning function.
The appliance displays the message “CLEANING!” above a
progressive bar.
You should not release the CLEAN button until the bar is
complete indicating that cleaning is concluded.
When the CLEAN button is released, the function stops.
After cleaning, remove the milk container and place in the
refrigerator.
The milk should not be left out of the refrigerator for more
than 15 minutes.
NOTE 4: To change the quantity of coffee or frothed milk the
appliance delivers automatically into the cup, proceed as descri-
bed in the section “Changing the quantity of coffee and milk for
cappuccino”.
CHANGING THE QUANTITY OF COF-
FEE AND MILK FOR CAPPUCCINO
The appliance is set by default to automatically deliver a normal
cappuccino.
To change these quantities, proceed as follows:
Changing the quantity of milk
• Fill the container with milk up to the maximum level indi-
cated on the container.
• Press the icon (B2) to enter the menu (fig. 15), then
press the icons (B7) and (B8) (fig. 2) until “PRO-
GRAM CAPPUCCINO” is displayed.
• Press the OK icon (B9) to confirm. “PROGRAM MILK” is di-
splayed.
• Press the OK icon (B9) again.
• Select the quantity of milk required by pressing the
icons (B7) and (B8). The progress bar shows the quantity of
milk selected.
• Press the OK icon (B9) to confirm (or the icon (B6) to
cancel the operation.
• Press the (B6) icon (B6) (fig. 18) twice to exit the
menu.
Changing the quantity of coffee
• Press the (B2) icon (B2) to enter the menu (fig. 15),
then press the icons (B7) and (B8) (fig. 2) until
“PROGRAM CAPPUCCINO” is displayed.
• Press the OK icon (B9) to confirm then the icons (B7
and (B8) (fig. 2) until “COFFEE FOR CAPPUCC.” is displayed.
• Press the OK icon (B9) again.
• Select the quantity of coffee required by pressing the
icons (B7) and (B8). The progress bar shows the
quantity of coffee selected.
• Press the OK icon (B9) to confirm (or the icon (B6) to
NO froth
“Denser” froth
frothed milk regulator
“Less dense” froth