eN
CNS
问题
可能原因
解决方案
熨斗已经开机，但底板仍未开始加热。
接线故障。
检查电源线、插头和电源插座。
温度控制开关处于最低
(MIN)
档位。
请选择合适的温度。
熨斗没有蒸汽。
水箱中的水量不足。
将水箱注满水（请参见“使用准备”
一章）。
蒸汽控制设定在“无蒸汽”档位。
将蒸汽控制旋钮设定到“最小蒸汽量”
至“最大蒸汽量”之间的位置
（请参见“织物熨烫温度设置表”
一章）。
喷雾功能无效
水箱中的水量不足。
将水箱注满水（请参见“使用准备”
一章）。
蒸汽喷射功能或垂直蒸汽喷射功能无效
在短时间内频繁使用蒸汽喷射功能。
将熨斗平放，稍等片刻后再使用蒸汽喷
射功能。
熨斗不够热。
将温度旋钮设定在一个适合蒸汽熨烫
的温度（最高可设置为
）。将熨斗
立放，直到温度指示灯熄灭后再开始
熨烫。
熨烫时水从底板漏出。
熨斗不够热。
将温度旋钮设定在一个适合蒸汽熨烫的
合适温度（
至最大温度）。
将熨斗放在熨斗架上，等到温度指示灯熄灭
后再开始熨烫。
在熨烫过程中底板内冒出水垢和杂质。
您使用了硬水，从而导致水箱内形成大量
水垢。
请一次或多次使用自清洁功能。
当熨斗冷却或存放后，水从底板漏出。
熨斗水平放置时水箱中还有水。
存放熨斗之前，请先将水箱清空，然后
将蒸汽控制设置为关闭。
Troubleshooting /
故障排除
Cleaning and care /
清洁与保养
/
清潔及保養
/
청소및관리
Problem
Possible cause
Solution
Soleplate is not heating, even though iron
is turned on.
Connection problem.
Check main power supply cable, plug
and outlet.
Temperature control is in MIN position.
Select adequate temperature.
Iron does not produce steam.
Not enough water in tank.
Fill water tank (see “Getting started”).
Steam control is selected in non-steam
position.
Set steam control between positions of
minimum steam and maximum steam (see
“Ironing chart”).
Spray function does not work.
Not enough water in tank.
Fill water tank (see “Getting started”).
Steam boost and vertical steam function
does not work.
Steam boost function was used very
frequently within a short period.
Put iron on horizontal position and wait
till it heat up before using steam boost
function again.
Iron is not hot enough.
Adjust the proper temperature to steam
ironing (up to
). Put iron in vertical
position and wait until temperature
indicator light turns off.
Water leaks from the soleplate during
ironing.
The iron is not hot enough.
Set the temperature dial to a temperature
(
to maximum) suitable for steam
ironing. Put the iron on its heel and wait
until the light has gone out before you
start ironing.
Flakes and impurities come out of the
soleplate during ironing.
You have used hard water, which has caused
scale flakes to develop in the water tank.
Use the self-clean function one or more
times.
Water leaks from the soleplate while the
iron is cooling down or after it has been
stored.
The iron has been put in horizontal position
while there is still water in the water tank.
Empty the water tank and set the steam
control to position off before storing the
iron.
11
