6.18. Service function / additional rinsing process
General information
Calling above-mentioned service function
w
Calling the Service Functions is similar with all designs
Calling the function "Additional Wash Cycle"
or key arrangements.
w
Always use the keys S1, S2, S3 and S4 independently
1.
Simultaneously press S2 and S4 and ...
from their program assignment depending on the model.
w
In service function mode, you can ALWAYS call "Selection
2.
... switch on the appliance with ON/OFF switch S1.
of an Add. Wash Cycle" with key combination S2 and S3.
Keep keys S2 and S4 pressed simultaneously
Use key S2 to modify the settings.
until the 3 acknowledging LEDs LD2, LD3 and LD4 are flashing.
w
From the works settings, no additional wash cycle is set.
(for abt. 4 seconds). Indicator LD1 at ON/OFF key lights up.
( Short-time illumination of LEDs is possible and does not constitute any fault)
3.
Simultaneously press S2 and S3 until the acknowledging LED
LED LD3 is flashing. LEDs LD3 and LD4 will go dark.
Indicator LD1 at ON/OFF key is lit.
The current status whether the additional wash cycle is activated
or not, is indicated in the display. If no display is available on
this model, the value is indicated by means of the "End" LED.
w
If this function is activated, an additional wash cycle
(also refer to Table left on this page)
is ALWAYS added, except for "prewash extra".
This will extend program run times up to
about 10 minutes. This additional wash cycle will be
Switching this function on or off:
executed until the function is deactivated again.
4. / 5.
Any further activation of function key S2 will
w
Table for the indication of on/off status:
switch the addition alternately on or off.
Abandoning the function
After the last activation of function key S2
you can leave the special program as follows:
After 60 seconds automatically all indications will go dark,
except for the LD1 of the ON/OFF key
or
Always applicable:
you switch the appliance off by means of ON/OFF key S1.
In order to call the totality of service functions always first
press the function keys S2 and S4 prior to switching the
Saving the status settings
appliance on by means of ON/OFF switch S1!
Immediately after each input of data, the currently valid status
Keep the keys pressed for abt. 4 seconds in order to
will be saved.
activate the function. This procedure is intentionally
distinguished from those for the customer functions.
ATTENTION:
In case of reduced key assemblies be sure
to observe Description Page B 1.
S1
Ein/Aus
LD1
S2
LD2
LD3
S3
S4
LD4
S1
Ein/Aus
LD1
S2
LD2
S3
LD3
S4
LD4
1.99
1.99
Tastenanordnung senkrecht
Tastenanordnung waagrecht
display
"End"-LED
if no display available
depending on variant
1d
on
Additional wash cycle selected
0d
off
No addititonal wash cycle
indication
comment
S1
On/Off
LD1
LD2
LD3
LD4
1.
2.
S1
On/Off
LD1
S2
LD2
LD3
S3
S4
LD4
LD1 is lit / LD2 - LD4 flashing
S2
S3
S4
S1
On/Off
LD1
S2
LD2
LD3
S3
1A
3.
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
END
LD1 is lit / LD3 flashing
... automatically Off after 60 sec.
... Off by actuating On/Off manually
0A
4.
END
5.
S1
On/Off
LD1
S2
LD2
LD1 leuchtet / LD2 blinkt
LD3
S3
S1
On/Off
LD1
LD1 leuchtet / LD2 blinkt
S2
LD2
LD3
S3
0A
END
if no display
available:
if no display
available:
if no display
available:
