6.13. Customer function / deactivation of signal sound:
General information
Calling / changing / saving the signal sound deactivation
The function deactivation of the signal sound does not exist
Calling the function "deactive signal sound"
generally and must be programmed in the software
1.
Switch on appliance with ON/OFF key S1
variant.
LD1 display with ON/OFF key is lit.
w
Deactivation resp. activation of the signal sound is executed
2.
Press keys S2 and S3 simultaneously until the
in all designs and key arrangements analogously.
confirmation LEDs LD2, LD3 and LD4 are flashing
w
For that you always have to use keys S1, S2, S3 and S4
LD1 display with ON/OFF key is lit.
independent of their variant-depending program load.
w
The key S4 is ALWAYS the "signal sound deactivation key"
3.
By actuating the function key S4 you now can call
w
The signal sound at the cycle end is always set active
the function signal sound deactivation. The confirmation
by the manufacturer.
LED LD4 continues flashing, LEDs LD2 and LD3 go out.
w
If the signal sound is deactivated it means that in general
The current condition whether the signal sound is active
no acoustic end signal will sound any more.
or not is indicated in the display.
The acoustic fault signals also cannot be heard any more!
If there is no display available depending on variant, the
value is indicated by the "END" LED.
(see for that the table on the left side of this page!)
Deactivation resp. activation of the signal sound:
4. / 5.
By any further actuation of the function key S4 you can
activate resp. deactivate the signal sound alternating.
Leaving the function
After the last key pressure of function key S4 you can
leave the special program as follows.
After 60 seconds all displays go out automatically,
except LD1 of the ON/OFF key
Table for indication of condition on/off:
or
the appliance is switched off by the ON/OFF key S1.
Saving the set condition
The condition is saved directly after any entry.
Generally, no wash cycle may be selected when calling the customer functions!
ATTENTION: In case of reduced key assemblies be sure to observe Description Page B 1.
S1
On/Off
LD1
S2
LD2
LD3
S3
S4
LD4
S1
On/Off
LD1
S2
LD2
S3
LD3
S4
LD4
1.99
END
1.99
END
vertical key arrangement
horizontal key arrangement
display
"END"-LED
if no display available
depending on variant
1b
on
signal sound (buzzer) on
0b
off
signal sound (buzzer) off
indication
comment
1.
2.
S1
On/Off
LD1
S2
LD2
LD3
S3
S4
LD4
END
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
1b
3.
S4
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
END
END
LD1 is lit / LD2 flashing
if no display
available:
... automatically Off after 60 seco
... Off by actuating On/Off manually
0b
4.
END
1b
5.
END
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
LD1 is lit / LD2 flashing
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
LD1 is lit / LD2 flashing
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
LD1 is lit / LD2 - LD4 flashing
if no display
available:
if no display
available:
