Electrolux ComfortLift ESF8735ROX Service Manual Download Page 26

Page: 26 / 60

The

Diamond Latch

is fixed on the door, and it’s possible to adjust the

iamond

atch's

position.

How to adjust the Diamond

atch

position

- Loosen the right screw of the

Diamond

Latch

until it spins.

- Do not loosen the left screw at the same

time.

- Push downwards with the screwdriver on

the screw to loosen the clamping lever.

- Lift up the

Diamond Latch

between 2

fingers.

- Push forward or backward (according

to needed adjustment).

- Push down until locked in position.

- Fix the right screw again to lock the

Diamond Latch.

If door is hard to keep closed: adjust

Diamond Latch

forward into the

dishwasher. If door is

hard to

clos

adjust out

wards

of the dishwasher.

Detail of the lever on the

Diamond Latch

26/60

Summary of Contents for ComfortLift ESF8735ROX





























































Search results

Summary of Contents for ComfortLift ESF8735ROX

Reviews:

Brands by name

Popular brands

Electrolux ComfortLift ESF8735ROX, Service Manual

Search results

Summary of Contents for ComfortLift ESF8735ROX

Reviews:

Brands by name

Popular brands