Electrolux Beam Installation Manual Download

Page: 8 / 16

Sharp 90° bend

Cable tie

NOGGIN with
55mm hole
allows pipe &
cable to go
through

This accessory is mounted on the connector
permanently unless being used, so some
thought should go into where it is to be
located.

VacPan Installation

Personal Clothes Brush Installation

Clothes brush connector must have LV cable
connected to it and must be hung far enough
above the inlet so that the hose of the Clothes
Brush hangs naturally. Ensure wires are insulated
from each other.

Low voltage cable running to clothes brush
connector NOT to the dedicated wall inlet.

A dedicated inlet must be used and it is
important to run the low voltage cable past the
inlet itself, up to the clothes brush connector.

Installing the Pipework

Timber Partition/Stud Walls

Side-On

Timber Partition/Stud Walls

Face-On (without inlet shown)

Screw in mounting
plate using only 1
flange into upright
timber (or noggin)

Inlet

Low voltage cable

Pipe bracket &
cable holder
screwed into
timber stud

Pipe bracket
securing pipe to
joist below floor

Kitchen Unit

Flexible Pipe

Jubilee Clip

Pipe

Plinth

Sharp 90° Bend

VacPan Inlet

LV cable

Summary of Contents for Beam

















Search results

Summary of Contents for Beam

Reviews:

Related manuals for Beam

Brands by name

Popular brands

Electrolux Beam, Installation Manual

Search results

Summary of Contents for Beam

Reviews:

Related manuals for Beam

Brands by name

Popular brands