background image

         

10

To reduce the risk of fire, electrical shock, or injury when using your appliance, please follow these basic
precautions including the following:

• Read all instructions before using your appliance.

• This Manual does not cover every possible condition and situation that may occur.  Use common sense and caution

when installing, operating and maintaining this appliance.

• FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS

IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

• The installation of this unit must conform to local codes or, in the absence of local codes, to all National Codes

governing plumbing, sanitation, safety and good trade practices.

BEFORE SERVICING, DISCONNET THE ELECTRICAL SERVICE  AND PLACE A RED TAG AT THE DISCONNECT
SWITCH TO INDICATE WORK IS BEING DONE ON THAT CIRCUIT.

NOTICE:

  CONTACT YOUR  AUTHORIZED SERVICE COMPANY TO PERFORM MAINTENANCE AND REPAIRS.

NOTICE:

  Using any parts other than genuine factory manufactured parts relieves the manufacturer of all warranty and

liability.

NOTICE:

  Manufacturer reserves the right to change specifications at any time without notice.

WARNING:

  The equipment warranty is not valid unless the appliance is installed, started and demonstrated under

the supervision of a factory trained installer.

WARNING:

  The unit must  be installed by Personnel who are qualified to work with electricity and plumbing.  Improper

installation can cause injury to personnel and/or damage to the equipment.  The unit must be installed in accordance
with applicable codes.

SAVE THESE

INSTRUCTIONS

SAFETY INSTRUCTIONS

Summary of Contents for AOFP061U












Reviews: