background image

         

15

Before using the appliance, clean the chamber with a detergent
solution, as there may still be condensation in the chamber left
over from the final testing by the manufacturers (see section D.1
for further information).

C.2.1 SWITCHING ON

Switch on the fused disconnet switch or the main circuit breaker
switch and press the 

I = ON

 button to start the appliance.  The

I = ON 

 indicator light lights up to signal that the appliance is

powered up.

C.2.2 OPERATION
C.2.2.1 Starting a “cruise chilling” cycle

To start the automatic “cruise chilling” (positive) cycle, insert

the core probe in the product and press the button

.

The cycle starts immediately when activated. To stop it, keep

the button  

 pressed for at least 3 seconds.

 IMPORTANT: The “cruise chilling” cycle is not

activated when the appliance is in “programme selection”

status

.....

C.2.2.2 Selecting a standard cycle

The default setting on the appliance is the SOFT chilling cycle.

Use these buttons  

 

  to select one of the following

options:

From left to right:

• Positive "SOFT CHILLING"
• Positive "HARD CHILLING"
• Positive "COOLER" maintenance (or preservation)
• Negative "BLAST FREEZING" chilling or freezing
• Negative "FREEZER" maintenance (or preservation)

When choosing a cycle, press the  

 button to move on to the

next option; the options are in a loop and so you can either scroll

forwards 

  or backwards 

 

 

.

If you want another cycle, keep pressing the 

  button until

the indicator light for the chosen cycle turns orange, and start it

by pressing the 

  button.

IMPORTANT:The appliance recognizes automatically when the
food (core) probe is inserted in to the product. If the probe hasn’t
been inserted in to the product, a timed cycle will start
automatically.
It is necessary to wait 2 minutes after the end of the preparation
cycle for the automatic recognition (see section below).

C.2.2.3 How to select a “turbo cooling” cycle

To select the  “turbo cooling” cycle, press the key 

; the

LED  

 will turn orange.

To start the cycle press the key  

.

C.2.2.4 Selecting a program:

First of all, the user has to decide what kind of cycle to launch
(SOFT, HARD, etc.) and then select the program.
Go through the following steps:
• Select the type of cycle;

• Press the program select button 

;

  the program indicator

light 

 lights up.

• press the select button 

  until the chosen program

indicator light 

 switches on.

• if the type of program is right, start it by pressing button 

.

if not

• keep pressing the select button 

  until the chosen

 C.2 USER INSTRUCTIONS

Summary of Contents for Air-O-Chill 727154




























Reviews: