F
F..7
7..2
2
C
Co
oo
okkiin
ng
g ttiim
me
e sse
ettttiin
ng
g
• Displays “6“ show the set cooking time.
• Press keys “8“/“9“ to increase/decrease the set value: the
display has a sensitivity of ±5 s and allows a minimum time
of 00:30s. (keeping keys “8“/“9“ pressed, the set time
changes faster).
• After setting, display “6” flashes for a few seconds, then the
value indicated will be stored.
• Press keys “3“/“4“ to start lowering the left/right lifter: the
corresponding display “6“ (left or right) will start the set time
count-down. On reaching the value 00:00, the cycle ends
with the lifter coming out of the oil bath and the display gives
the value initially set.
F
F..7
7..3
3
P
Prro
og
grra
am
mm
miin
ng
g
5 different cooking programmes (keys “10“) can be stored: the
desired cooking temperature and, depending on the version, 1
or 2 cooking times can be stored in each programme (in the
”full optional” versions there are the times of the two baskets R.
H./L.H.).
To store a programme, enter the desired values and press one
of the keys p1... p5 until an acoustic signal indicates storage.
Carry out the same procedure to store other cooking
programmes.
NOTE!
At the time of installation no programmes are stored
and each subsequent storage cancels the pre-
existing programme.
F
F..7
7..4
4
P
Prro
og
grra
am
mm
miin
ng
g b
bllo
occkk
The keypad can be blocked, enabling use of only the
previously stored programmes.
To enable/disable this option:
• After switching on the appliance, press the key “7“. FASt
(Fast Food) will appear on the display;
• Press key “2“: if Y (Yes) appears on the display keys “7“, “8“
and “9“ are blocked; if n (no) appears keys “7“, “8“ and “9“
are activated;
• Press keys “7“” to change the parameter (Y/n). Press key
“2“ to store;
• To quit the Fast Food menu, press keys “3“ and “4“ together.
F
F..7
7..5
5
U
Ussiin
ng
g a
a sse
ett p
prro
og
grra
am
mm
me
e
• Press one of the keys “10“ for the programme, displays “5“
and “6“ show the stored settings;
• Press key “3“ or “4“ to start cooking.
F
F..8
8
D
Drra
aiin
niin
ng
g o
oiill
• Emptying the tanks should be done at cold oil;
• Switch the fryer off;
• Pay maximum attention to avoid coming into contact with
the hot oil;
F
F..8
8..1
1
7
7L
L // 1
15
5L
L // 4
40
0L
L B
Bu
uiilltt--iin
n vve
errssiio
on
nss
Open the drain tap, slowly turning the knob (“A“) anticlockwise;
F
F..8
8..2
2
7
7L
L // 1
15
5L
L C
Co
ou
un
ntte
err T
To
op
p vve
errssiio
on
nss
position a bowl for collecting the oil at the drain valve (“B“)
(fig.2); above the valve there is a small knob (“A“) which must
be pressed (1) and slowly turned (2) clockwise to discharge the
oil.
F
F..8
8..3
3
A
Allll vve
errssiio
on
nss
• Close the drain tap by turning the knob.
NOTE!
For better appliance performance, regularly change
the oil. Overusing an oil reduces its flashpoint and
increases its tendency to boil suddenly.
G
G
M
MA
AC
CH
HIIN
NE
E C
CL
LE
EA
AN
NIIN
NG
G A
AN
ND
D M
MA
AIIN
NT
TE
EN
NA
AN
NC
CE
E
G
G..1
1
O
Orrd
diin
na
arryy m
ma
aiin
ntte
en
na
an
ncce
e
G
G..1
1..1
1
IIn
nffo
orrm
ma
attiio
on
nss ffo
orr m
ma
aiin
ntte
en
na
an
ncce
e
Routine maintenance operations can be carried out by non-
specialised personnel, carefully following the instructions
given below.
NOTE!
The manufacturer declines any liability for opera-
tions carried out on the machine without following
these instructions.
G
G..1
1..2
2
C
Clle
ea
an
niin
ng
g tth
he
e a
ap
pp
plliia
an
ncce
e a
an
nd
d a
acccce
esssso
orriie
ess
Before using the appliance, clean all the internal parts and
accessories with lukewarm water and neutral soap or products
that are over 90% biodegradable (in order to reduce the
A
A
B
1
2
25
