Electrolux 318 203 869 Use And Care Manual Download Page 46

Page: 46 / 52

Surface Burner Grate

Surface Burner Caps

Surface Burner Head

cautioN

use caution when replacing the burner head so the electrode is not damaged. a damaged electrode

may cause a delayed ignition or prevent the burner from igniting

Any additions, changes or conversions required in order for this appliance to perform satisfactorily

must be made by a qualified service technician.

General Care & Cleaning

CLEANING THE BURNER GRATES, BURNER CAPS AND

buRneR heads

the cooktoP is not ReMoVable.

Do not attempt to remove or lift the cooktop.

The Grates, Burner Caps and the Large 18k Burner Head

should be routinely cleaned. Keeping the burner ports clean

will prevent improper ignition and an uneven flame. If needed,

the fixed burners should be cleaned in place with an humid

cloth (do not spraw water on them).

Refer to the following instructions:

To Remove and Replace the Surface Burner Grate,

Surface Burner Cap and Surface Burner Head -

Remove

in the following order; (1st) Surface Burner Grate, (2nd)

Surface Burner Cap, (3rd) Surface Burner Head (See Figure

1).

Reverse the procedure above to replace the Surface Burner

Cap, Surface Burner Head and Surface Burner Grate.

not remove any burner parts from the cooktop until

the burner parts have completely cooled and are safe

to handle. Do not operate the surface burners without

the Surface Burner Heads, Surface Burner Caps and

Surface Burner Grates properly in place.

1st

2nd

3rd

Orifice

Electrode

Surface Burner

Head

Surface Burner

Cap

Figure 1

Surface Burner

Grate

To Clean the Burner Caps, Burner Heads and Burner Grates -

Use a soap-filled

scouring pad or a mild abrasive cleaner to clean the surface burner caps and surface

burner heads. The Grates are designed to be Dishwasher safe for cleaning. The ports (or

slots) around the burner heads must be routinely cleaned. If residue still remains in these

ports, use a small-gauge wire or needle to clean the slots or holes being careful not to

damage the electrode. For proper flow of gas and ignition of the burner—

DO NOT ALLOW

SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE

GAS ORIFICE HOLDER OPENING. ALWAYS

make sure that the surface burner cap, the

surface burner head and the surface burner grate are properly in place whenever a surface

burner is in use.

Summary of Contents for 318 203 869





















































Search results

Summary of Contents for 318 203 869

Reviews:

Related manuals for 318 203 869

Brands by name

Popular brands

Electrolux 318 203 869, Use And Care Manual

Search results

Summary of Contents for 318 203 869

Reviews:

Related manuals for 318 203 869

Brands by name

Popular brands