Electrolux Professional UNIC TANGO ACE-ST DUO Manual Download Page 63

Page: 63 / 67

Tango 390-00322 7-2022

The SteamAir wand MUST be wiped

and purged after each use to prevent

milk build-up

Remove the pitcher and

wipe the wand and tip with a

clean, damp towel.

Press SteamAir Button

Steam will automatically

shut OFF at the pre-set

temperature

Steam Wand should be

centered in the pitcher

Tip must be at least 1” below

surface of milk

Press the Steam or the

SteamAir Button

ON then OFF

to purge

Automatic Milk Steaming:

Turn the adjusting collar

to vary the amount of air

in the milk

•

• •

•

••• More air

• Less air

Steam or Water leaking from

the top of the wand ?

No Foam in milk?

Steam tip is clogged with milk

See next page for

cleaning instructions

More air creates lighter foam with larger bubbles

Less air creates denser foam with smaller bubbles

Remove and clean the

steam tip daily!

SteamAir Wand Operation

ace

Summary of Contents for UNIC TANGO ACE-ST DUO




































































Search results

Summary of Contents for UNIC TANGO ACE-ST DUO

Reviews:

Related manuals for UNIC TANGO ACE-ST DUO

Brands by name

Popular brands

Electrolux Professional UNIC TANGO ACE-ST DUO, Manual

Search results

Summary of Contents for UNIC TANGO ACE-ST DUO

Reviews:

Related manuals for UNIC TANGO ACE-ST DUO

Brands by name

Popular brands