Electrolux Professional UNIC TANGO ACE-ST DUO Manual Download Page 53

Page: 53 / 67

Tango 390-00322 7-2022

Startup - Operation:

Machine will not start up, displays:

“Warming up, please wait…”

Grounds Drawer not fully seated

Check switched, wires, and plug CN20

Water shut off during startup

Check water filters, water pressure switch, plug CN9

Turntable Turns full circle on startup, or doesn’t stop over Waste Drawer

ABS setting too high (set all the way to 40)

ABS is the braking system for the Turntable, normally leave at default setting of 0

Find in: settings; other setings; tamping & preinfusion - scroll to bottom of list

Steam and water buttons grey

& Drink Icon appears briefly on screen when selected, does not brew

Machine in Demo mode: #8 DIP top switch on CPU set to “1”, change to “0”

All Screen Buttons Grey and not functioning

Software versions in Display Screen and CPU are not compatible

Update both using the same USB

Turntable piled with wet coffee

Brew valve exhaust blocked by water in drain

Make sure machine is mounted with slight forward tilt so drain manifold empties.

Machine won’t switch ON;

Main contactor doesn’t engage. Toggle switch not lighted

Faulty ON/OFF Toggle switch

Faulty main 10A fuse

Machine won’t switch ON

;

Main contactor doesn’t engage. Toggle switch lighted

F3 Fuse, 24volts on board

F4 Fuse

Faulty contactor coil

Summary of Contents for UNIC TANGO ACE-ST DUO




































































Search results

Summary of Contents for UNIC TANGO ACE-ST DUO

Reviews:

Related manuals for UNIC TANGO ACE-ST DUO

Brands by name

Popular brands

Electrolux Professional UNIC TANGO ACE-ST DUO, Manual

Search results

Summary of Contents for UNIC TANGO ACE-ST DUO

Reviews:

Related manuals for UNIC TANGO ACE-ST DUO

Brands by name

Popular brands