background image

Installation manual

29

7 Electrical connection

The electrical installation may only be performed by qualified personnel.
Electrical connection of the cabinet must be done in accordance with electrical safety regulations.
Make sure that the connection current is in line with the data on the identification plate and that the mains cable
is grounded properly according to the applicable standard. We recommend that the mains cable be equipped
with a ground fault interrupter.
The manufacturer disclaims all liability if the electrical connection is not done in the manner prescribed in this
manual.

The drying cabinet must be connected to an all-pole circuit breaker.

Heating options

Mains voltage

Hz

Heat output

kW

Total output

kW

Recommended fuse

A

Electrically heated

400V 3N ~

50

9.0

9.1

16 slow-blow

7.1

Network Functions

Note!

Can only be used on premium products.

This product can be connected to ELS VISION or to an external payment system.

fig.W01529

Connecting to ELS Vision

Connect the network cables GND, RX, TX, 24V to the terminal block as illustrated.
Connect the neutral position switch to terminal block positions 1 and 2, as illustrated.

Activate the connection to ELS Vision as follows:
Press and hold the Stop button, and then press both program buttons.
ACCESS 0000 is shown in the display.
Enter the code 9191.
Enter the numbers using the program buttons; press Stop.

Summary of Contents for DC6-14





































Reviews: