ElectroCraft SCA-LE-30-03 User Manual Download Page 2 | Manualshive

Page: 2 / 32

background image

User Manual SCA-LE-30-03

Table of Contents

Safety & Installation .................................................................... 3

Specifications: ............................................................................. 4

Drive Overview ............................................................................ 6

Wiring ......................................................................................... 10

Explanation of Terminals, Dip Switches, & Potentiometers .. 13

Glossary ..................................................................................... 17

Description of Inputs and Outputs .......................................... 24

Basic Troubleshooting ............................................................. 28

Accessories & Options ............................................................. 29

Warranties & Disclaimers ......................................................... 30

Dimensions ................................................................................ 31

Mounting Din rail adapter ......................................................... 32

Used Symbols

Indicates a warning or caution concerning operations that may lead to
death or injury to persons, or damage to property if not performed correctly.
In order to use the drive safely, always pay attention to these warnings.

Indicates a clarification of an operation, or contains additional explanations,
or operational requirements for a procedure. Reading these notes is much
recommended.

ElectroCraft

®

E-Mail: [email protected] www.electrocraft.com May 2009

2

«
1
2
3
4
...
»

Summary of Contents for SCA-LE-30-03

































Reviews:

No comments

Related manuals for SCA-LE-30-03

Brand: Sprint Electric Pages: 8

Brand: EWM Pages: 10

Brand: Danfoss Pages: 2

Brand: Becker Pages: 20

Brand: Becker Pages: 24

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 84

Brand: GM International Pages: 8

Brand: Shihlin Pages: 4

Brand: KB Electronics Pages: 5

Brand: KB Electronic Pages: 18

Brand: Sanhua Pages: 5

EtherCAT EHS-580

Brand: Econ Pages: 36

Brand: HAUTAU Pages: 8

Brand: ZIEHL-ABEGG Pages: 28

Brand: YASKAWA Pages: 106

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands