background image

10 

 

LEAK TESTING 

NEVER USE A NAKED FLAME TO CHECK FOR LEAKS.  

NEVER LEAK TEST WHILE SMOKING. 

The gas connections on this appliance are leak tested at the factory prior to 

shipment.  

This appliance needs to be periodically checked for leaks and an immediate 

check is required if the smell of gas is detected. 

 

Make a soap solution using 1 part of liquid dish-washing soap to 3 parts 

water. The soap solution can be applied with a soap bottle, brush, or rag 

to the leak tested points shown in the figure above.  

 

The  valve  of  the  gas  cylinder  should  be  in  the 

OFF 

position.  Once  the 

soapy  solution  is  applied  to  the  gas  connections,  the  valve  of  the  gas 

cylinder needs to be turned to the 

ON 

position.  

 

Soap bubbles will begin to form in the soapy solution if a leak is present. 

 

In case of a leak, turn off the gas supply. Tighten any leaking fittings, then 

turn the gas supply on and recheck. 

 

GAS REQUIREMENTS 

 

The regulator and hose assembly used must conform to local safety requirements. 

 

Never  use  a  gas  cylinder  with  a  damaged  body,  valve,  collar,  or  foot  ring. A  dented  or  rusty  gas  tank  may  be 
hazardous and should be checked by a gas supplier. 

 

Never connect this appliance to an unregulated gas source. 

 

When the appliance is not in use, turn the gas cylinder OFF, before disconnecting it. 

 

Always perform a leak test on gas connections whenever a cylinder is connected. If bubbles form in the leak test 
solution, do not use. Never use a flame to test for leaks.  

 

CONNECTING TO A GAS CYLINDER

 

 

Use a 9 kg gas cylinder. 

Please refer to your gas supplier for suitable gas cylinder. 

 

Refer to your gas supplier for instructions on the use of your gas cylinder. 

 

Only change gas cylinders outdoors or in a well-ventilated area away from naked flames and any other source of 

ignition. 

 

The gas cylinder must always be used in an upright position.  

 

Close the heater control dial by turning fully clockwise. 

 

Close the gas cylinder tap and then attach the regulator onto the gas cylinder.  

 

Tighten all connections firmly and with a spanner where appropriate. The cylinder should be located on the cylinder 

base. 

 

Check for leaks at all joints using soapy water. If a leak is found, tighten the joint and then re-test.

 

 

 

 

Leak Test Point 

 

 

 

 

Summary of Contents for EQODHMBR














Reviews: