Electra Roman Blinds How To Install, Programme And Operate Download Page 12

Page: 12 / 16

STEP

3 -

To reverse

the direction of the
motor, press and hold
the 'my' button

for

approx 2 seconds

until the blind jiggles.

Reprogramme

STEP

Press and hold

simultaneously the Up
and Down buttons

for

approx 5 seconds until the
blind jiggles.

Reset

and reprogramme

procedure

Before you begin - Disconnect the power to all other

powered

blinds while programming.

Reset

STEP 1

Disconnect the battery pack.

STEP

2 -

Remove the blind and the battery pack from their mounting brackets and lay out on a table.

STEP

Reconnect the battery pack.

STEP

4 -

Initiate reset

Take a paper clip and press and

press

the

reset

button

in the recessed hole

beside where the power cables enter the motor. Hold until the

blind j

iggles

3 times (approx 12 secs). All

setting

are deleted and the motor has been reset.

STEP

2 -

Press

the

down button. Does
the blind move down?

YES- the blind moves down
while pressing the down
button - Go to step

NO - the blind moves up
while pressing the down
button - continue to step

Press with a paperclip

for approx 12 secs

STEP 5 - Disconnect the battery pack.
STEP 6- Refit the blind and battery pack.
STEP 7 - Reconnect the battery pack, then follow the

reprogramme steps below.

Summary of Contents for Roman Blinds

















Search results

Summary of Contents for Roman Blinds

Reviews:

Related manuals for Roman Blinds

Brands by name

Popular brands

Electra Roman Blinds, How To Install, Programme And Operate

Search results

Summary of Contents for Roman Blinds

Reviews:

Related manuals for Roman Blinds

Brands by name

Popular brands