page 5/6
4 insTallaTiOn seTup
4.1 verifying the accuracy of the connections and connecting the power supply
check the correctness of the connections in the installation!
The
+14 V
,
C/D
and
GND
signals are the same for all components of the installation.
Any short-circuit between them will affect all the indoor terminals, causing them not to function.
connect the power supply to the
230 V a.c.
network through a
10 A
automated fuse!
Optionally, the accumulator is connected to the
+ACC
;
-ACC
hubs of the
SAC.V1A.DIN
power supply.
Pay attention to the connection to the correct polarity of the outdoor accumulator!
check the correct functioning of the power supply:
•
The measured tension at the hubs of the power supply:
+14 V
⟷
GND / 13,8 ÷ 14,3 V d.c.
• Power supply signaling, according to the following table:
Signaling
Observations
Network tension
Tension presence:
+14 V
,
+Uv
1
S1 permanent Green
S2 permanent Green
The installation is ready to function.
If the audio or video communication is not functioning, check the
status of fuses Sig. 1 and Sig. 2 from the power supply.
230 V ± 10%
50 Hz
+14 V
⟷
GND
13,8 ÷ 14,3 V d.c.
+Uv
⟷
-Uv
13,5 ÷ 15,0 V d.c.
2
S1 alternating Red / Green
S2 permanent Green
The installation is functioning.
Charging accumulator.
3
S1 alternating Red / Green
+ acoustic signaling
S2 permanent Green
The installation is functioning.
Faulty or uncharged accumulator: replace the accumulator!
4
S1 permanent/flashing Red
S2 turned off
The installation is functioning
only on audio communication,
for a limited amount of time.
Check the power fuse from the network and fuse Sig. 3.
NO:
0 V
+14 V
⟷
GND
10,5 ÷ 13,8 V d.c.
+Uv
⟷
-Uv
NO:
0 V
5
S1 flashing Green
S2 turned off
The installation is NOT functioning.
Shortcircuit in the installation on
+14 V
and/or
+Uv
.
Eliminate the shortcircuit and re-establish the connection!
230 V ± 10%
50 Hz
NO:
0 V
4.2 programming the Tags
The Red Programming TAG contains the unique code of the installation company.
When an outdoor panel reads a Programming TAG for the first time, it is personalized with the company’s unique code.
The code is permanently registered in the panel’s memory and can only be erased at the producer.
The personalized panel will not accept the Programming TAGs of other installation companies.
how to program the Tags’ access codes in the memory of the outdoor panel:
The door on which the lock is mounted will remain closed the entire time it takes to program the TAGs! Entering the programming mode with the
door open will erase all acces codes.
1. Use the Red Programming TAG!
The panel enters the Programming Mode: [
BEEP
BEEP
BEEEEEEP
]
The Programming mode closes
automatically
if the panel is idle for more than 10 seconds or
imediately
by using the Programming TAG once more.
2. You now have a maximum of 10 sec. for each Access TAG.
You will hear the following sounds:
•
[
BEEP
BEEP
] when the Access Code has been succesfully memorized,
•
[
BEEP
BEEP
] when the TAG’s Access Code is already in the panel’s memory,
•
[
BEEP
] when the panel has been idle for 10 seconds and is no longer in the Programming Mode.
To erase all the access codes from the panel’s memory:
This action cannot be undone! The panel will not recognize any Access TAG.
1. Enter the Programming Mode!
(by using the Programming TAG)
2.
Operate the lock’s button
*
for at least 6 seconds!
Acoustic confirmation: [
BEEP
BEEP
BEEP
]
*
If the lock does not have a button, you need to short-circuit between the BUT and LC hubs (of the outdoor panel) for at least 6 seconds.
4.3 programming the address of the additional outdoor panel
Remember:
The default address of all oudoor panels is 1.
The installation must have one outdoor panel with the adress 1. This will be the main panel.
The outdoor panels must have unique addresses within the installation.
The installation does not work if 2 panel’s share the same address!
how to program the additional outdoor panel:
The door on which the lock is mounted will remain closed the entire time it takes to program the additional panel!
1. Use the Red Programming TAG on the additional panel!
The panel enters the Programming Mode: [
BEEP
BEEP
BEEEEEEP
]
The Programming mode closes
automatically
if the panel is idle for more than 10 seconds or
imediately
by using the Programming TAG once more.
2. Press any key!
[
BEEP
] when the panel’s address increases by +1, [
BEEP
BEEP
BEEP
] when the panel is bak to having address 1.
For the following 10 seconds, the additional panel is still in the Programming Mode and you may proceed to program its Access TAGs.
