background image

19

To order replacement and/or spare parts for your SCOOT - N - GO™.,  make 

sure you call the Electra Customer Service / Technical Support Toll-Free 

Number 1-888-467-1234 M-F 10am - 9pm EST or view the SCOOT - N - GO™  

replacement parts available at www.electraUSA.com.

TROUBLE SHOOTING

Problem

1. Scooter motor does not run

2. Scooter does not accelerate

3.  The actual driving range is 
     shorter than the estimated range

Possible Cause

1. Key ignition is in OFF position

2. Fuse has burned out/failed

3.  Battery is undercharged

1. Battery is undercharged or 
     completely drained
2. Electric throttle is not attached or in 
    need of repair
3. Drive chain has become unseated

1. The tires are under inflated

2. The battery is undercharged

3.  Poor riding conditions

4.  Weight of rider

5. Drive Chain

Correction

1. Rotate  Key  to ON position

2. Remove, inspect, and replace 
    with additional fuses from tool kit
3.  Charge the battery for a sufficient 
      amount of time; replace battery

1. Charge the battery for a sufficient 
      amount of time; replace battery
2. Check all throttle connections and 
     wiring; replace throttle if necessary
3. Reseat the drive chain on both 
    sprockets and adjust tension

1. Inflate to 45-50 PSI 
2.  Charge the battery for a  sufficient 
         amount of time;  replace battery
3. Do not ride in sand, ice, snow, or 
    unstable riding areas
4.  Mfg. suggest rider not exceed
     178 lbs.

5.  Adjust Drive chain tension

REPLACEMENT PARTS

If your SCOOT - N - GO™ sustains an impact:

  

A CRASH OR OTHER IMPACT CAN PUT EXTRAORDINARY STRESS ON COMPONENTS, CAUSING THEM 

TO FATIGUE PREMATURELY. COMPONENTS SUFFERING FROM STRESS FATIGUE CAN FAIL SUDDENLY 

AND CATASTROPHICALLY, CAUSING LOSS OF CONTROL, SERIOUS INJURY OR DEATH.

First, check yourself for injuries, and take care of them as best you can.  Seek medical help if necessary. 

Next, if your SCOOT - N - GO™ is damaged, perform the checks described in this manual.  If you are 

unable to fix any or all damage/problems, or if you find any bent, scored, or discolored parts, please call 

Electra  Customer  Service  at  1-888-467-1234  M-F  10am  -  9pm  EST  or  visit  the  Electra  website  at 

electraUSA.com for replacement parts.

  

IF YOU HAVE ANY DOUBT ABOUT THE CONDITION OF THE SCOOT - N - GO™  OR ANY OF ITS PARTS, 

CALL  ELECTRA  CUSTOMER  SERVICE  AT  1-888-467-1234  M-F  10AM  -  9PM  EST  AND  THEY  WILL 

ASSIST YOUR IN PERFORMING A THOROUGH CHECK.

Summary of Contents for Scoot-N-Go 88615


























Reviews: