manualshive.com logo in svg

Electra Accessories Scoot-N-Go 88615, Assembly And User'S Manual, Page: 17 / 25

Share
Download
Electra Accessories Scoot-N-Go 88615 Assembly And User'S Manual Download Page 17

16

STARTING INSTRUCTIONS 

1. Make sure you have READ ALL SAFETY GUIDELINES AND PRE-RIDE ADJUSTMENTS IN THIS MANUAL

2. Make sure battery is fully charged

3. Check brakes

4. Insert key in ignition and turn right

5. Check throttle

6. Check all lights

7. Rotate throttle to accelerate

DRIVE CHAIN

*Refer to Pre-Ride Adjustments in this manual

BRAKES

*Refer to Pre-Ride Adjustments in this manual

 

FLAT TIRE REPAIR

To change a tire or inner tube, it is a good idea to keep the SCOOT - N - GO™ tool kit with you when 

you ride. You should also carry plastic "tire levers" (available at local bike shops), a spare inner tube that 

fit the wheel and tire size available from Electra at www.electraUSA.com or by calling Customer Service 

at 1-888-967-1234 M-F 10am-9pm EST as well as a manual hand pump to re-inflate the tire if you have 

a flat or it becomes low during use. 

1. Depress the tire valve to let all the air out of the tube.

2. Remove the wheel from the scooter using the wrench provided or your own wrench. Loosen the 

nuts by turning counterclockwise.  Be sure to remember where all the spacers and washers belong.  For 

rear tire removal you will also need to slip the chain off the rear sprocket to remove the wheel. The 

chain must be properly reinstalled and re-tensioned when reinstalling the rear wheel. Make certain the 

chain is properly position on both front and rear sprockets before re-tightening rear wheel.

3. Remove one bead of the tire from the rim by grasping it at a point opposite the valve stem with both 

hands and, at the same time, lifting and peeling one side of the tire off the rim. If the bead is on too 

tight for you to unseat it with your hands use tire levers to lift the bead carefully over the tire rim. Tire 

levers can be purchased at any local bike shop. Push the valve stem through the wheel rim. Remove 

the inner tube.

4.  Carefully  check  the  outside  and  inside  of  the  tire  for  the  cause  of  the  puncture  and  remove  any 

debris or damaging material from the inside or outside of the tire. 

Continued on Next Page

SERVICE & MAINTENANCE

Summary of Contents for Scoot-N-Go 88615


























Reviews:

No comments