background image

 

 

 
 

CONTENTS 

 

1.

 

IMPORTANT SAFETY INSTRUCTIONS ........................................................................................... 3

 

2.

 

PRODUCT OVERVIEW .................................................................................................................... 3

 

3.

 

GENERAL INSTALLATION INSTRUCTION ..................................................................................... 5

 

3.1 Mounting instructions ...................................................................................................................... 5

 

3.2

 

Pipe work ...................................................................................................................................... 6

 

3.3

 

Flow direction ................................................................................................................................ 6

 

3.4 Connection ..................................................................................................................................... 7

 

3.6 Electrical connection ....................................................................................................................... 8

 

4.

 

OPERATING INSTRUCTIONS ......................................................................................................... 9

 

4.1 Flow requirements .......................................................................................................................... 9

 

4.2 Lamp life indicator ........................................................................................................................... 9

 

4.3 Water quality ................................................................................................................................... 9

 

5.

 

MAINTENANCE .............................................................................................................................. 10

 

5.1 Essential parts to carry out annual maintenance including our reference codes ........................... 10

 

5.2 Lamp replacement and quartz sleeve cleaning ............................................................................. 11

 

6.

 

DISPOSAL OF ELECTRICAL/ELECTRONIC EQUIPMENT ........................................................... 13

 

7.

 

WARRANTY ................................................................................................................................... 14

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for CLASSIC H.R. UV-C SPA

















Reviews: