background image

| 6

1. 

Check  whether  the  collar  fits  tightly  or  not.

 If 

necessary, adjust it. You must cut the excess strap.

2.  Install the collar block in the middle of the strap.

 

Note that the collar block moves along the strap 

as you pull on it.

3.  You must put the collar on the dog so the block is 

in the center of the throat.

 The collar reacts to the 

vibration of the throat when the dog barks.

How to put a collar on a dog:

IMPORTANT!

Read on for more details and features of use!

The collar 

needs to be charged

 when the 

red light 

continues flashing slowly for 

30sec

 and then turns 

off automatically.
1.  Open the Battery Charging Rubber Cover on the 

Anti Bark Collar, plug one end of the cable in the 

charging port and connect the other end 

to the 

adaptor, computer, notebook, 

or

 power bank. 

(Note: please make sure that the adaptor output is 

5V/500 - 1000mAh.) 

2.  Plug the Lithium Polymer Charger into an electrical 

power outlet of standard household voltage (110-

230V) based on your local standard. 

3.  The red light will be steady when fully charged 

within 

1.5 to 2 hours.

 It turns green light when 

charged fully.

INSTRUCTION

CHARGING

Summary of Contents for DC-656












Reviews: