A
B
A
B
A
B
E
F
H
G
43 mm
10 mm
Ø
Model
RTS26E5001B02
ON/OFF
RTS26E5001B03
OFF/ON
Technical Details
Frequency:
868.30 MHz
Radiated power:
0.34 mW
Modulation:
FSK
Coding:
Easywave
Power supply:
1x 3-V-battery, CR2032
Operating
temperature:
-20 °C to +60 °C
Range:
free-field: approx. 150 m
buildings: approx. 30 m
Dimensions (w/l/h):
33/166/8 mm
Weight:
34.0 g (incl. battery)
Scope of Delivery
Window handle contact RTS26, magnetic disc,
battery holder, battery CR2032, operating inst-
ruction
Intended Use
Only use the radio window handle contact
RTS26 to transmit radio signals to Easywave re-
ceivers.
The manufacturer shall not be liable for any da-
mage caused by improper or non-intended use.
Safety Advice
Before using the Radio Wall Switch,
carefully read through the operating
instructions!
Also note the operating instructions of the
receiver(s)!
Please check regularly the ready-to-transmit-
state of the device!
Have faulty devices checked by the manufactu-
rer!
Do not make any unauthorized alterations or mo-
difications to the device!
Keep the batteries out of the reach of children!
Function
The window handle contact RTS26 is a magnetic
contact that signaled the open/closed status of a
window and transmits an alarm telegram wireless
to an Easywave receiver.
The variants of RTS26 differ in function:
RTS26 Window Handle Contact ON/OFF and OFF/ON
GB
ON/OFF
(RTS26E5001B02): If the window is
opened, the Easywave code A (ON) is sent and
if the window is closed the Easywave code B
(OFF) is sent.
OFF/ON
(RTS26E5001B03): If the window is
opened, the Easywave code B (OFF) is sent and
if the window is closed the Easywave code A (ON)
is sent.
By pressing the button on the window handle con-
tact transmits the status of the grip position OPEN
or CLOSE and displays them through the LED.
LED lights up red means grip position is ON. LED
lights up green means grip position is CLOSED.
So can be checked that the installation of the
magnetic disk is correct.
T
he transmitter has a battery check function,
which checks the capacity of the battery during
the transmission process. (see chapter „Control-
ling the Battery“).
The window handle contact is suited for standard
window handles with a rod dimension of 7 mm,
screw dimension of 10 mm and a hole spacing
of 43 mm.
A
Battery holder with
battery CR2032
B
Magnetic disc
C
Button and LED green/red
D
Easywave receiver
E
Magnet
F
Reed contact
G
Square bar max. 7 mm
H
Protective film from the
adhesive pad
Start-Up
1. Insert the enclosed battery into the battery
holder (A) and put these into the RTS26.
Use only batteries of type CR2032. Make
sure the polarity is correct.
The positive pole
has to be visible!
2. Teach the transmitter code to the re-
ceiver. Please read the operating ins-
tructions supplied with the receivers.
Press the button (C) briefly, the LED lights up
red. The transmitter code has been learned.
3. Unscrew the window handle while the window
is closed. Remove the protective foil from the
rear adhesive pad (H) of the window handle
contact and stick this onto the window frame.
Observe the correct position (the drill holes
must be vertically aligned).
4. Insert the magnetic disc (B) in the window
handle contact.
The magnet must point to
the reed contact
(F)
.
5. Move the window handle through the magne
-
tic disc (B) back into the window and screw
the handle on again.
D
B
A
C
A
B
