GB
Power Plug Radio Repeater RXP03
Models
Scope of Delivery
Teaching in the transmitter
Reset (Deleting Memory Completely)
Deleting Specific Transmission
Codes
Safety Advice
The unit may only be used as a Repeater for
Easywave telegrams.
The manufacturer shall not be liable for any
damage caused by improper or non-intended
use.
Intended Use
Function
Wall outlet
Programming button and
LED view
GB
F/B (PL)
D(A/NL/S/N)
CH
RXP03-5001E-01
868.30 MHz
D
-02
868.30 MHz
GB
-04
868.30 MHz
F/B
-05
868.30 MHz
CH
RXP03-5001E
RXP03-5001E
RXP03-5001E
Power plug radio repeater RXP03, operating
instructions
Please read these instructions
carefully before using the device!
We do not accept any liability for personal
injury or damage to property caused by
incorrect handling or non-observance of the
safety instructions!
Observe the valid laws and regulations as well
as the manufacturer's instructions
Attention!
Observe the admissible supply
voltage and the maximum contact load of the
wall outlet (16 A, 230 V AC / 50 Hz)!
for the
devices to be operated!
Frequency:
868.30 MHz
Modulation:
FSK
Transmission delay:
300 ms
Operating voltage:
230 V AC / 50 Hz
Power consumption: 80 mA
Leistungsaufnahme: 0,7 W (stand by)
Protective class:
II
Protective type:
IP 20
Operating temp::
-20°C to +60°C
:
60%
:
Power plug
(
)
:
16 A / 230 V AC
(WxHxT) 50 x 120 x 75 mm
Weight:
Range:
open field:
approx.
150 m
buildings:
approx.
30 m
Max. relative air
humidity
Mains output
non switchable
Max. contact load
Dimensions
approx. 190 g
Technical Details
The Power Plug Radio Repeater receives
radiograms of Easywave transmitters and re-
transmits these radiograms with a transmission
delay of 300 ms. So the range of Easywave radio
transmitters can be extended.
The transmission codes of the corresponding
Easywave transmitters have to be memorized by
the repeater so that specific radiograms are re-
transmitted.
1. Briefly (< 1.6 sec.) press the programming
button. The LED flashes.
2. Press and hold a transmitter button. As soon
as the code has been memorized, the LED
lights up for 4 seconds and then flashes
again. Release the transmitter button.
3. Repeat step 2 with the other transmitters. The
repeater can memorize up to 16 transmitter
codes.
4. To return to the operating mode briefly
(< 1.6 sec.) press the programming button.
After memorizing the first transmitter code, the
repeater only re-transmits the radiograms of
memorized transmitters.
In case of a longer power failure the programming
of the repeater remains.
In the reset mode you can delete all codes the
repeater has memorized.
1. Keep the programming button pressed for
more than 1.6 sec. The LED flashes rapidly.
2. Press the programming button again and
keep it pressed for more than 1.6 sec. As
soon as the memory has been deleted
completely, the LED lights up for 4 sec. and
than flashes again rapidly.
3. Briefly (< 1.6 sec.) press the programming
button in order to return to the operating
mode.
Note:
If all codes have been deleted, the repeater
will re-transmit every Easywave telegram again.
In the delete mode you can delete specific
transmitter codes.
1. Keep the programming button pressed for
more than 1.6 sec. activated. The LED
flashes rapidly.
Start Up
1.
The repeater is ready
for operation now.
2.
As long as no Easywave transmitter code is
memorized by the repeater, every received
Easywave telegram will be re-transmitted.
During receiving a radiogram, the LED flashes
for a short time. During re-transmission, the LED
flashes a little bit longer.
Plug the repeater into a
properly functioning earthed
outlet.
Attention!
Ensure an inter-
ference-free wireless con-
nection. Do not install the device in a
distribution box, metal housings or close to
large metal objects
Teach the coding of the Easywave
transmitter into the repeater (see section
"Teaching in the transmitter").
PROG
Disposal
Conformity
Customer Service
Put the packaging material into the
recycling bins for cardboard, paper and
plastics.
Dispose of the waste product via a collec-
tion point for electronic scrap or via your
specialist dealer.
Waste electrical products should not be
disposed of with household waste!
The product fulfils the essential require-
ments of the R&TTE directive
1999/5/EG.
Warranty
We will remedy defects on the device based on
material or production errors within the statutory
warranty period or exchange the device.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty null
and void.
For application in: EU/CH/FL/IS/N
The Declaration of Conformity can be found on
the internet at: www.eldat.de.
General Information
If the device does not work properly despite
proper handing or in case of damage, please
contact your retailer.
ELDAT GmbH
Im Gewerbepark 14
D-15711 Zeesen
Germany
Phone: + 49 (0) 33 75 / 90 37-0
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-mail: [email protected]
Have malfunctioning devices checked by the
manufacturers!
Do not open the appliance's casing!
Do not make any unauthorized alterations or
modifications to the unit!
2. Press the selected transmitter channel
button. As soon as the code has been
deleted, the LED lights up for 4 sec. and then
flashes again rapidly.
3. Repeat step 2 with another transmitter or
briefly (< 1.6 sec.) press the programming
button in order to return to the operating
mode.
98805 0511 D/GB