Elcon LT2MSKU-T Operating Instructions Manual Download Page 2

 
 LT2MSKU-T 

LT2MSKU-T 

 

 

Version: 2008/05/23 

Version: 2008/05/23 

 

10

 

Miscellaneous 

 
Please keep this manual always accessible at a safe place! 
 
When putting the device into operation, pay attention to the safety precautions (

 chapter 11). 

 
We reserve the right to apply modifications. This is contributed to the technical progress and 
aimed at the permanent improvement of the product.  

 
 

11

 

Safety precautions 

 
For your own safety, please observe the following hints. Read them carefully before you put 
the device into operation. 
 

Precautions against electrostatic discharge 

Upon opening and installation of the components of the SHDSL transmission system, atten-
tion shall be paid to the safety precautions as stipulated by IEC 61340-5-1. 
 

Safety precautions during thunderstorms 

Keep away from manipulations on the SHDSL transmission system and its components 
during thunderstorms (Do not disconnect or connect sub-units or cables). 
 

Grounding and potential equalization  

During installation, operation and maintenance of the SHDSL transmission system, the 
regulations as set out in IEC 60364-5-54 shall be observed. 
 

Warning of dangerous electric voltage 

The SHDSL transmission system has got interfaces being under dangerous electric voltage. 
Therefore, all works on the system should be performed by personnel who has acquired the 
necessary special knowledge. 
 
 
 

Summary of Contents for LT2MSKU-T















Reviews: