background image

 Owner's Manual

 

 

 

 

6.5

 

 

 

Always tow or be towed at slow speed. Never exceed the hull speed of a 
displacement craft when towing or being towed.

Breaking strength of forward strong point: 69,4 kN =7,1 tonnesf = 7072 kg

It is the owners / operators responsibility to ensure that the mooring lines, 
towing lines, anchor chains, and anchors are adequate for the vessel's 
intended use. Owners should also consider what action will be necessary 
when securing a tow line on board.

The breaking strength of lines / chains should not exceed 80% of the 
breaking strength of the strong point to which it is attached.

Caution

Information

Caution

Anchoring, Mooring & Towing

When at anchor, it is damaging to leave the full load of the boat resting 
on the windlass. It is recommended that the chain be tied onto a local 
strong point. 

Caution

Information

A tow line shall always be made fast in a way that it can be released 
when under load.

Caution

Always replace bulbs with one of the same wattage.

Caution

Navigation lights may be marked with expiry dates. Ensure that they are 
replaced as required.

Caution

Check for proper operation of navigation lights before heading out and 
carry replacement bulbs for all navigation lights

 

  Technical Software

© Licensed User: Elan d.o.o., 2019

38/44

Summary of Contents for Impression i40.1













































Reviews: