background image

TWINSPOT IP65 EMERGENCY INSTALLATION INSTRUCTIONS

8

12. WIRELESS DAUGHTERBOARD

13. SELF TEST/ STANDARD WIRING/ CENTRAL BATTERY SYSTEM

The Twinspot inverter also supports an optional wireless daughterboard. The driver must be disconnected 
from mains and battery must be removed, before installing or changing any expansion module. More 
information and a list of other accessories can be found in the 

Wireless design and installation guide. 

The 

assembly for this part onto the inverter is shown below:

The inverter can be used in an automatic self-test mode which reduces the need for a test switch timer.
The self-test ability automatically disables if the unit is wired to DALI or the wireless daughterboard is attached.
Additionally the third generation platform can be wired to a central battery system. With this wiring the system 
cannot report the light status (see

 Self test support 

document for more information).

Figure 7: Daughterboard assembly diagram

Figure 8: Inverter standard wiring diagram

2

1

Wireless daughterboard (6118)(optional)
Twinspot inverter (1231, 1248, 1249, 1250)

1
2

Installer wired

Prewired

Summary of Contents for 1706

















Reviews: