background image

TWINSPOT IP65 EMERGENCY INSTALLATION INSTRUCTIONS

14

26. WARRANTY INFORMATION

Ektor products are distributed in Australia and New Zealand by Evolt Pty Ltd (Evolt). 

The Australian Consumer Law as well as other Australian laws guarantee certain conditions, warranties and 

undertakings, and give you other legal rights, in relation to the quality and fitness for purpose of Ektor products 

sold in Australia. 

In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You 

are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable 

loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable 

quality and the failure does not amount to a major failure. What constitutes a major failure is set out in the 

Australian Consumer Law.

Nothing in this Warranty purports to modify or exclude the conditions, warranties and undertakings, and other 

legal rights, under the Australian Competition and Consumer Act and other Australian laws. 

Ektor products are warranted in Australia for a period of 12 months from the date of delivery of the product, 

provided that the products are properly stored, installed, used and maintained in accordance with the instructions 

contained within their manual. 

Products that have been altered in any way or used other than in accordance with their instructions are not 

covered by this Warranty.

This Warranty is not transferable and is valid only in the hands of the purchaser of the product. The warranty 

does not cover Ektor products other than those purchased from Evolt. Proof of purchase must be provided to 

Evolt with any warranty claim. Evolt recommends that the purchaser attaches their proof of purchase to their 

product manual.

If you wish to claim under this Warranty, you must, at your own expense, return the product or that part of 

the product which you believe is defective, and proof of original purchase, your name, address and telephone 

number and a certificate of installation or other document required by the law for the installation of electrical 

products in the place in which the product was installed, to Evolt at the address above within 12 months from the 

date of purchase. Please note that the Warranty does not cover removal or reinstallation of the product or that 

part of the product which you believe is defective.

Evolt’s total liability under this Warranty is limited to the cost of repair or replacement of the faulty product. Evolt 

may satisfy its obligations under this Warranty in full by repair or replacement of a faulty product. 

This Warranty does not apply to consumable items such as lamps or batteries or other items that can be classified 

as consumable. 

For the avoidance of any doubt, any and all warranties or conditions which are not guaranteed under the 

Australian Competition and Consumer Act or the Australian Competition and Consumer Regulations 2010 and 

which are not expressly included in this Warranty as additional warranties or conditions are excluded.

This Warranty does not cover loss or damage caused by wear and tear, misuse, incorrect installation or 

operation, failure to clean and maintain, incorrect voltage or non-authorised electrical connections, adverse 

external conditions (such as power surges and dips, acts of God, exposure to heat, corrosion, insect or vermin 

infestation), use of non-authorised or defective parts or globes, or to items that have been repaired other than by 

Evolt or a repairer approved by Evolt. 

Summary of Contents for 1706

















Reviews: