background image

SERVICE MANUAL

 

 

SM-eVENT-GB-3_8-2006.doc

 

3

 

 

1.  WARNINGS  

1.1. 

CE Marking   

Products  marked  with 

CE

  mark  of  compliance  meet  safety  guidelines  of  European  Union 

(93/42/EEC). 
  

1.2. 

General warnings 

• 

The  installation,  operation  and maintenance manual is an integral part of the appliance. It is 

necessary  to  always  keep  this  document  close  to  the  appliance.  Strict  observance  of  this 
manual is a prerequisite for the correct operation of the appliance.  

• 

The safety of operating personnel and failure-free operation of the appliance are ensured only 

when  using  the  original  components  of  the  appliance.  It  is  possible  to  use  accessories  and 
spare parts mentioned in the technical documentation or clearly permitted by the manufacturer. 

• 

When used with non authorized accessories or consumable material, the manufacturer cannot 

assume responsibility for the safe operation and functionality of the device. 

• 

The  Guarantee  does  not  cover  damages  that  originate  due  to  the  use  of  non  authorized 

accessories or consumable material other than those recommended by the manufacturer.  

• 

The manufacturer assumes responsibility regarding safety, reliability and function only if 
-  The  installation,  calibration,  amendments,  extensions  and  repairs  are    made  by  the 

manufacturer  or  his  representative  or  a  service  organization  authorized  by  the 
manufacturer, 

-  The  appliance  is  used  in  accordance  with  the  installation,  operation  and  maintenance 

manual. 

• 

The installation, operation and maintenance manual, at the time of printing, corresponds to the 

design of the appliance and its state according to the relevant safety and technical standards. 
The manufacturer reserves all copyrights for the given wiring schemes, methods and names. 

 

1.3. 

General safety  warnings  

The  manufacturer  developed  and  constructed  the  appliance  so  that  damage  would  not  occur 
when the appliance is used for its intended purpose. The manufacturer considers it his obligation 
to describe the following safety measures in order to avoid further damages. 

• 

When operating the appliance, it is necessary to observe laws and regional regulations valid in 

the  place  of  usage.  In  order  to  ensure  safe  course  of  works,  the  operator  and  user  are 
responsible for the observation of regulations 

• 

The  original  packaging  should  be  kept  for  the  possible  return  of  the  unit.  Only  original 

packaging guarantees an optimal protection of the appliance during transportation. If it would 
be  necessary  to  return  the  appliance  during  warranty  period,  the  manufacturer  is  not 
responsible for damages caused by incorrect packing. 

• 

It is necessary that the user ensures the appliance is safe to use prior to usage. 

• 

The user must familiarize himself with the correct operation of appliance. 

• 

If an undesirable event occurs in the operation of appliance, the user is obliged to immediately 

inform his supplier to this event. 

• 

This product is not intended for use in areas with the risk of explosion. 

  

1.4. 

Safety warnings regarding the protection against electric current  

• 

The  appliance  must  only  be  connected  to  an  appropriate  power  source  that  has  correct 

grounding. 

PDF created with pdfFactory trial version 

www.pdffactory.com

Summary of Contents for DK50 D






























Reviews: