11
AFTER USAGE
Be careful when cleaning up the tip of the camera (near the lens part)to avoid a contact to the lens.
It may cause a blurry image or malfunction if any contact has been made to the lens.
• Do not use any chlorine bleach or a volatile organic solvent, like benzene or thinner, or a
chemical fiber duster. It may cause a damage or a scratch on the product.
• Do not use in any sterilizer such as a autoclave machine.
■
Maintenance and Cleaning
• Store this product in a box when not using for a long time. Or store it in a charging stand and
keep it where water may not splash and no dust may not be generated.
• Store this product in a box when not using for a long time. Or store it in a charging stand and
keep it where water may not splash and no dust may not be generated
Transport or store this product in a following condition.
Temperature: Between –5
℃
(23°F) to 50
℃
（
122°F
）
Humidity: Between 20%RH to 80%RH (Avoid condensation or freezing)
Atmospheric pressure: Between 750hPa (750mB) and 1060hPa (1060mB)
■
Storage and Transport
Pack this product carefully with a buffer or cushioning material, and put them into a proper-sized
box (cardboard or crate). Make sure the product stays still with cushioning materials in the box.
While transportation, avoid water or dust to contact the inside and avoid a strong shock to the
box.
■
When Transport
■
Please dispose the used disposable covers or lens protective sheets, following by
regulations or legislations in your area.
• Whether the functions listed on the user guide operate normally.
• Whether camera is used normally after charging.
• Whether there are no loose screws on the camera body.
• Whether there are no cracks on the body.
• Whether the AC Adaptor is connected properly.
■
Safety Check (Recommended to be done monthly)
Do not reuse the same disposable cover each time.
Keep this product clean by cleaning up in the following way:
12
Q & A (Troubleshooting)
The white LEDs (4 lights) of
the camera are on, but
there is no picture on the
display.
〈
After checking the channel setting, confirm the followings:
〉
TV… Confirm your TV is set on the “input” channel.
PC (with USB Morse):
PC (with Morse with a video capture card and other dental
imaging software):
[
With RF receivers
]
Is the channel setting correct? Set the channel on the receiver to
the corresponding camera channel. The camera channel is
indicated on the hand piece (refer to Page 10).
[
On Doctor’s Station Monitor
]
Is the channel setting correct?
Set the channel on the Doctor’s Station monitor to the
corresponding camera channel (refer to the user guide of
Doctor’s Station for more details).
1
）
Is your camera fully charged?
Charge the camera (refer to Page 9).
2
）
It may be caused by “Multi Path Interference”.
Please change the location of the receiver and the camera.
3
）
Is there any airport, military base or radio station
within 3 km / 2 miles radius?
If so, please contact RF technical support
(E-mail: [email protected]).
4
）
Is there any equipment that might generate electromagnetic
noise (i.e., PC, monitor, TV, printer, or a video player)?
Please change the location to 30cm (a foot) away from such
equipment.
5
）
Is the power switch “ON”?
Make sure to slide the power switch to “ON”. If it is on “SLEEP”, it
goes to the sleep mode.
There are lines/noises on the
displayed image.
Confirm the selected device is correct under Digital
Video Input Setting on the software (refer to the user
guide of USB Morse for more details).
Confirm the selected video source is correct for
your video capture card on the software (consult
how to import the images from the video capture
card with your software manufacturer, as each
software has different setting procedures).
(Refer to Page 2 for more details.)
The camera has the on-board CPU and the CPU is controlling all
operation. Therefore, there may be an occasion that it freezes
(stops working) similar to a computer. For such case, press the
reset button with fine-tipped object to reset the unit. Be aware
that pressing the reset button will erase all stored images in
Einstein Lumica.
The power does not turn
on/off by sliding the power
button.
