GB
- 17 -
not use the tool without the additional handle.
The additional handle (8) is secured to the ham-
mer drill by a clamp. During the handle clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
•
The supplied additional handle (8) must
first be fitted. To do this, the clamp must be
opened by turning the handle until it is wide
enough for the additional handle to be slid
over the chuck (1) and on to the hammer drill.
•
After you have positioned the additional
handle (8), turn it to the most comfortable
working position for you.
•
Now turn the handle in the opposite direction
again until the additional handle is secure.
•
The additional handle (8) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop (Fig.
4/Item 2)
The depth stop (2) is held in place by the additi-
onal handle (8) by clamping. The clamp can be
released and tightened by turning the handle.
•
Release the clamp and fit the depth stop (2)
in the recess provided for it in the additional
handle.
•
Set the depth stop (2) to the same level as
the drill bit.
•
Pull the depth stop back by the required dril-
ling depth.
•
Turn the handle on the additional handle (8)
until it is secure.
•
Now drill the hole until the depth stop (2) tou-
ches the workpiece.
5.3 Fitting the drill bit (Fig. 5)
•
Always pull the power plug before making ad-
justments to the equipment.
•
Release the depth stop as described in 5.2
and push it towards the additional handle.
This provides free access to the chuck (1).
•
Open the chuck by turning it anti-clockwise
with the supplied chuck key (9)
•
The drill bit opening must be large enough to
fit the drill bit into.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Tighten the chuck (1) by turning the chuck
key (9) clockwise until the drill or tool is secu-
re. Checkt that the drill is secure in the chuck
(1)
•
Check at regular intervals that the drill bit or
tool is secure (pull the mains plug).
6. Operation
6.1 ON/OFF switch (Fig. 6/Item 5)
•
First fit a suitable drill bit into the tool (see
5.3).
•
Connect the mains plug to a suitable socket.
•
Position the drill in the position you wish to
drill.
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
Important! Locking is possible only in clockwise
rotation.
To switch o
ff
:
Press the ON/OFF switch (5) brie
fl
y.
6.2 Adjusting the speed (Fig. 6/Item 5)
•
You can infinitely vary the speed whilst using
the tool.
•
Select the speed by applying a greater or les-
ser pressure to the ON/OFF switch (5).
•
Select the correct speed: The most suitable
speed depends on the workpiece, the type of
use and the drill bit used.
•
Low pressure on the ON/OFF switch (5): Lo-
wer speed (suitable for: small screws and soft
materials)
•
Greater pressure on the ON/OFF switch (5):
Higher speed (suitable for large/long screws
and hard materials)
Tip:
Start drilling holes at low speed. Then increa-
se the speed in stages.
Bene
fi
ts:
•
The drill bit is easier to control when starting
the hole and will not slide away.
•
You avoid drilling messy holes (for example
in tiles).
6.3 Preselecting the speed (Fig. 6/Item 6)
•
The speed setting ring (6) enables you to
define the maximum speed. The ON/OFF
switch (5) can only be pressed to the defined
maximum speed setting.
•
Set the speed using the setting ring (6) on the
ON/OFF switch (5).
•
Do not attempt to make this setting whilst the
drill is in use.
Anleitung_TC_ID_500_E_SPK8.indb 17
Anleitung_TC_ID_500_E_SPK8.indb 17
15.11.2017 10:11:14
15.11.2017 10:11:14
