noise etc., e.g. the number of machines and other
neighboring operations. Reliable workplace values
may also vary from country to country. With this
information the user should at least be able to make a
better assessment of the dangers and risks involved.”
Total vibration values (vector sum of three directions)
determined in accordance with EN
13898
.
Vibration emission value a
h
= 1.068 m/s
2
Reduce noise generation and vibration to a
minimum!
Use only equipment that is in perfect condition.
Maintain and clean the equipment regularly.
Adapt your working methods to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
6. Before starting the equipment
6.1 General information
Before commissioning the machine, it must be
firmly mounted on a workbench; fully assemble
the underframe that came with the unit or similar.
All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the blade to run freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws, etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine’s moving parts run smoothly.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the machine to the power supply.
6.2 Assembling the saw (Fig. 1-3; 6)
To adjust the turntable (17), loosen the locking
grip (14) by approx. 2 turns, which frees the
turntable (17).
Press the latched position lever (13), turn the
turntable (17) and scale pointer (15) to the
desired angular setting on the dial (16) and lock
into place with the locking grip (14). The saw has
locking positions at angles of - -45°, -30°, -22.5°, -
15°, 0°, 15°, 22.5°, 30°, 45° and 60°, at which you
can engage the latched position lever.
To release the saw from its position at the bottom,
pull the fastening bolt (27) out of the motor
mounting while pressing down lightly on the
machine head (4). Turn the fastening bolt (27)
through 90° before releasing it, so that the saw
remains unlocked.
Swing the machine head (4) up until the release
lever (3) latches into place.
The clamping devices (8, 21) can be fitted on the
left or right of the fixed saw table (18).
Undo the locking screws for the roll base (30).
Guide roll base with limit stop (9) over one of the
holding bars for the roll base (10) and install on
the fixed saw table (18), tightening the
appropriate locking screw (30) (Figure 6).
Mount the second holding bar for the roll base
(10) on the opposite side of the saw and secure
with the appropriate locking screw (30).
When the locking screw (22) is loosened, you can
tilt the machine head (4) to the left by up to 45°.
If the saw is used without the base frame, the foot
(32) will prevent the saw from tipping forwards
during operation. In this case, turn out the foot
(32) until it touches the surface on which the saw
is standing.
6.3 Assembling the base frame and bolting the
saw to the base frame (Fig. 4-24)
1. Insert the feet (A) from the bottom into the
intermediate struts (C) as shown in Figure 7.
Ensure that the rubber stoppers on the feet (A)
are aligned so that the support surfaces are level.
2.
Screw the feet (A) to the intermediate struts (C)
together with the screws (N), washers (H) and
nuts (G), as shown in Figures 8 - 9.
3.
Guide the side parts (B) from the top over the
intermediate struts (C).
4.
At each connection point screw the side parts (B)
to the intermediate struts (C) using three screws
(L), washers (K) and nuts (I) (Figures 11-12).
5.
Insert the two bottom cross struts (E) into the
appropriate openings on one of the intermediate
struts (C) as far as the stop (Figure 13). Screw
the bottom cross struts (E) to the intermediate
strut (C) using two screws (L), washers (K) and
nuts (I) in each case, as shown in Figures 14 - 15.
6.
On the same side of the base frame, slide the two
top cross struts (F) as far as the stop into the
appropriate openings on the side part (B) (Figure
16). Insert a corner bracing (D) into each opening
on the side part (B). Note, that each of the corner
bracings (D) only fits on one side of the base
frame; this is the case when the openings on the
side part (B), the top cross struts (F) and the
corner bracings are positioned precisely on top of
each other (Figure 17).
7.
Now screw the top cross struts (F), corner
bracings (D), side parts (B) together using two
screws (L), washers (K) and nuts (I) in each case,
as shown in Figures 18 - 19.
23
GB
Anleitung_RT_XM_305_U_SPK7:_ 14.03.2012 14:36 Uhr Seite 23
