EN
- 13 -
could impair operation and shorten the life of
the equipment.
The connection to the water inlet must be
fi
tted
with a connector for standard hose coupling
systems (Fig. 7 / Item 11). Pass a water hose
(approx. Ø 13 mm (½“)), through the additional
handle as shown in Fig. 14 and attach the hose
coupling to the connection for the water inlet (Fig.
15). Remove the hose clip (Fig. 2 / Item 7) from
the long handle and secure the hose to the long
handle with the hose clip (Fig. 16/17).
The supplied water control valve (Fig. 22/Item 26)
can be
fi
tted to the connector for the water inlet as
an option. The valve enables you to regulate the
water intake with stepless adjustment or interrupt
the water intake.
Each time before use, check the following :
•
That the equipment is in perfect condition and
that the safety devices and the cleaning brush
are complete.
•
That all screws are securely fastened.
•
That all moving parts move smoothly.
5.8 Fitting the battery (Fig. 18)
Push the battery into the battery mount provided.
The battery will be heard to click into place when
it has been pushed fully in. To take out the battery,
press the pushlock button (Item 21) and remove
the battery.
6. Operation
Please note that the statutory regulations
governing noise abatement may di
ff
er from one
location to another.
Danger!
The brush covers on the side must be
fi
tted when carrying out work.
Warning!
•
Make sure that you have fitted the brush
which is intended to be used for the surface
you want to clean.
•
Make sure that the brush covers on the side
are fitted securely.
•
Inspect the brushes to check them for dirt
before you start your cleaning work and clean
them if necessary.
•
Carry out a test run on a small area which is
not very visible to check that brushing does
not damage the surface.
•
The surface to be cleaned must be free of
objects such as stones, twigs, etc. These
could be flung up by the rotating brush or
scratch the surface.
•
Lift the equipment 0.4-0.8 inches (1-2 cm)
off the ground when you switch it on, but only
until it has reached full speed. Take care when
doing so in order to prevent injuries.
•
Never switch on the equipment while it is
tilted or while it is lifted for any other purpose
than for reaching the full speed – risk of injury!
•
Never use the equipment for too long at any
one point.
•
We recommend wet cleaning. Only use clean
water without any additives whatsoever.
•
Keep your hands and feet away from the
rotating brush.
•
Only insert the battery just before you start
your work and remove it again when you have
finished.
6.1 Changeover switch (Fig. 20)
Note:
•
Using the changeover switch you can select
the direction of rotation of the equipment
and lock it so that it cannot be switched on
accidentally. You can select between forward
and reverse rotation. Forward is the standard
direction of rotation, with which the equipment
has the most power.
•
Hold the equipment firmly by the handle and
additional handle and make sure you have a
steady standing position.
•
To avoid causing damage to the equipment,
the direction of rotation must only be changed
when the equipment is at a standstill.
a)
Forward (standard direction of rotation):
Slide switch on left (24) pressed - the
equipment pulls away from you.
b)
Safety- lock-o
ff
:
Slide switch in the middle
position (as shown) - On/O
ff
switch blocked
c)
Reverse:
Slide switch on right (25) pressed -
the equipment moves towards you.
6.2 On/O
ff
switch (Fig. 18 / Item 3)
a) Switching on
When you press the On/O
ff
switch, the brush
rotates.
b) Switching o
ff
When you release the On/O
ff
switch, the
equipment switches o
ff
and the brush comes
to a standstill.
Anl_Picobella_SPK7_USA.indb 13
Anl_Picobella_SPK7_USA.indb 13
01.07.2020 11:37:55
01.07.2020 11:37:55
