GB
- 7 -
4. Technical data
Motor power supply: ............................... 18 V DC
Idling speed: ...........................11000-20000 min
-1
Sanding/grinding area: ............. 90 x 90 x 90 mm
Oscillation angle: ...........................................3.2°
Weight: .....................................................0.86 kg
Important!
The equipment is supplied without rechargeable
batteries and without a charger and is allowed to
be used only with the lithium-ion batteries of the
Power-X-Change series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with Power-
X chargers.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L
pA
sound pressure level ........................ 78 dB(A)
K
pA
uncertainty .............................................3 dB
L
WA
sound power level .......................... 89 dB(A)
K
WA
uncertainty .............................................3 dB
Wear ear-mu
ff
s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Handle
Vibration emission value a
h
= 13.9 m/s
2
K uncertainty = 1.5 m/s
2
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level speci
fi
ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before using the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger.
5.1 Fitting the plug-in tools (Fig. 1/2)
•
To fit the plug-in tools safely you should
hold the multifunction tool so that the On/Off
switch (1) points down and the tool chuck (2)
faces up.
•
Place the plug-in tool (e.g. the triangular
grinding/sanding plate or HCS saw blade) on
the tool mounting (2) so that the pins of the
tool mounting (2) fit into the recesses in the
plug-in tool.
•
Secure the plug-in tool using the supplied
socket head screw (14) and tighten the screw
securely with the hexagon key (5).
Anl_TC_MG_18_Li_SPK7_UKCA.indb 7
Anl_TC_MG_18_Li_SPK7_UKCA.indb 7
04.06.2021 11:28:51
04.06.2021 11:28:51
