GB
- 18 -
The multifunction display (5) indicates the charge
level during charging as shown by the 5 LEDs.
0-15%: All LEDs
fl
ash
15-35%: LED 1 is lit, LEDs 2-5
fl
ash
35-55 %: LED 2 is lit, LEDs 3-5
fl
ash
55-75 %: LED 3 is lit, LEDs 4-5
fl
ash
75-90 %: LED 4 is lit, LED 5
fl
ashes
Ready for operation: All the LEDs are lit
Important! The handle may become a little warm
during the charging process. This is normal.
If the battery fails to charge, please check
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
If the battery still fails to charge, send
•
the charger
•
the equipment
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and
fi
res.
5.2 Inserting the various tools (Figs. 3-4)
Danger!
Before inserting a tool (and before each tool
change) switch of the drive unit.
1. Press the locking knob (3) and turn the collet
chuck until the bolt locks into place.
2. Remove the clamp nut (2) using the chuck
key (20), insert the matching clamping sleeve
(21) and re
fi
t the clamp nut.
3. Insert the required tool (b) into the sleeve as
far as the stop and tighten the clamp nut (2)
using the chuck key (20).
The projection is not allowed to exceed 25 mm!
6. Starting up
6.1 On/O
ff
switch (Fig. 1)
To switch the device on, press the On/O
ff
switch
(1).
To switch the device o
ff
, press the On/O
ff
switch
(1) again.
6.2 Speed selector (Fig. 5)
The required speed can be set with the speed
controller (7).
•
Press the + button to increase the speed.
•
Press the – button to decrease the speed.
You can choose from 5 speed settings. The cur-
rent speed during operation is shown on the mul-
tifunction display (5).
Important!
The speed that you set beforehand is saved and
is retained when the device is started up again.
When used for the
fi
rst time and after charging,
the device starts in setting 3.
The correct speed depends on the tool used and
the type of material being processed.
6.3 Information on speed settings
•
Small cutters/grinding pins: High speed
•
Large cutters/grinding pins: Low speed
6.4 Work practice
•
Exert only moderate pressure on the work-
piece so that it can be machined at constant
speed.
•
Instead of accelerating your work, high pres-
sure will cause the drive unit to slow down
and even stop, thus overloading the motor.
•
For your own safety, it is essential to secure
small workpieces with a screw clamp or vise.
•
Precision work/engraving: Hold the drive unit
like a pen (single-handed).
•
Rough work: Hold the drive unit like the hand-
le of a hammer (two-handed).
6.5 Battery capacity indicator (Fig. 5 /Item 6)
The battery charge level indicator (6) lets you
know when the device needs recharging again
during operation.
The LED is lit green: The rechargeable battery is
charged to between 20% and 100%.
The LED is lit red: The remaining charge is less
than 20%. Recharge the battery.
Anl_TE_MT_7_2_Li_SPK9.indb 18
Anl_TE_MT_7_2_Li_SPK9.indb 18
14.04.2020 10:34:50
14.04.2020 10:34:50
